Delkevic exhaust - must install rear brake arm one spline tooth CCW from witness mark on end of shaft to avoid interference with exhaust pipe and then

Delkevic exhaust - must install rear brake arm one spline tooth CCW from witness mark on end of shaft to avoid interference with exhaust pipe and then

  • 0
  • 0
Polished Risers And Triple Clamp_2

Polished Risers And Triple Clamp_2

  • 1
  • 2
650 tank damper as installed for 750 tank swap

650 tank damper as installed for 750 tank swap

  • 0
  • 4
Delkevic 2-into-1 stainless steel exhaust installed 05Aug2015 - using both supplied baffles - re-installed stock foot controls because OSS rear brake

Delkevic 2-into-1 stainless steel exhaust installed 05Aug2015 - using both supplied baffles - re-installed stock foot controls because OSS rear brake

  • 0
  • 0
Nat'l Cycle N2543 Flyscreen

Nat'l Cycle N2543 Flyscreen

  • 1
  • 0
14Apr2016 Back to a 19" front rim and tire - they match the 18" rear better than the 21" I had on earlier

14Apr2016 Back to a 19" front rim and tire - they match the 18" rear better than the 21" I had on earlier

  • 0
  • 0
14Apr2016 right-side view with new 19" front wheel

14Apr2016 right-side view with new 19" front wheel

  • 0
  • 0
CVK left view - installed 29Jun2015 w/ 38 pilots, 138 mains, JJJ needles, 3rd clip slot, shortened JEGS choke cable, mount for push cable cut off

CVK left view - installed 29Jun2015 w/ 38 pilots, 138 mains, JJJ needles, 3rd clip slot, shortened JEGS choke cable, mount for push cable cut off

  • 0
  • 1
Sleeve-and-grommet anti-vibration mount for front turn signals using 1/8" custom aluminum bracket. Shortened OEM housings drilled and tapped for 3/8"

Sleeve-and-grommet anti-vibration mount for front turn signals using 1/8" custom aluminum bracket. Shortened OEM housings drilled and tapped for 3/8"

  • 0
  • 0
clubfoot sidestand - installed 18Jul2015

clubfoot sidestand - installed 18Jul2015

  • 0
  • 0
1/2" bore m/c - brake switch wiring plugs right in

1/2" bore m/c - brake switch wiring plugs right in

  • 0
  • 0
3/4" copper pipe end caps shortened & center-drilled to fit 650 tank dampers for 750 tank install (must enlarge damper ID slightly)

3/4" copper pipe end caps shortened & center-drilled to fit 650 tank dampers for 750 tank install (must enlarge damper ID slightly)

  • 0
  • 1
With Stainless Mesh

With Stainless Mesh

  • 1
  • 0
2F3 Headlight Swap

2F3 Headlight Swap

  • 0
  • 0
Vented Side Cover

Vented Side Cover

  • 0
  • 0
Yamaha TW200/XT225/TTR250 Master Cylinder - 11mm bore diameter. Perfect for the stock late-model, single-piston caliper but too sensitive for a 4-pot

Yamaha TW200/XT225/TTR250 Master Cylinder - 11mm bore diameter. Perfect for the stock late-model, single-piston caliper but too sensitive for a 4-pot

  • 0
  • 0
CVK right view

CVK right view

  • 0
  • 0
Cafe/Sport Seat; 18" XSPerformance rear rim w/ Bridgestone Battleax 110/90-18 BT45 tire on TX750 swing arm

Cafe/Sport Seat; 18" XSPerformance rear rim w/ Bridgestone Battleax 110/90-18 BT45 tire on TX750 swing arm

  • 0
  • 0
IMG_3099

IMG_3099

  • 0
  • 0
Bobbed turn signal housing attached to lower fork clamp using custom "mule ear" bracket designed for sleeve-and-grommet anti-vibration mounting method

Bobbed turn signal housing attached to lower fork clamp using custom "mule ear" bracket designed for sleeve-and-grommet anti-vibration mounting method

  • 0
  • 0
1/2" bore m/c from Yamaha XV250 Virago - good size to use with 4-pot, 65mm Brembo caliper - not the best angle for mirror stem - installed 20Jul2015

1/2" bore m/c from Yamaha XV250 Virago - good size to use with 4-pot, 65mm Brembo caliper - not the best angle for mirror stem - installed 20Jul2015

  • 0
  • 0
brake cable adjuster used to adapt stock XS650 throttle cable to Keihin 34 CVK's (shortened stock cable 1 3/8") - installed 14Jul2015

brake cable adjuster used to adapt stock XS650 throttle cable to Keihin 34 CVK's (shortened stock cable 1 3/8") - installed 14Jul2015

  • 0
  • 0
4-pot Brembo caliper - left side view

4-pot Brembo caliper - left side view

  • 0
  • 0
22Jun2014 - left side view showing OSS mid shifter

22Jun2014 - left side view showing OSS mid shifter

  • 0
  • 0
A

Redleg's '82 Heritage Special

A work in progress - some mod's I've made so far after buying in April 2010
Click to expand...
There are no comments to display.

Album information

Album owner
aldo5468
Date created
Item count
59
View count
8,645
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

A

aldo5468

Media items
59
Albums
1
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top