Recent content by KennyD77

  1. KennyD77

    Valve Seat Cutters

    Good! Did you get the radius cutters also?
  2. KennyD77

    Valve Seat Cutters

    I think so (don't take that to the bank tho) at thexscafedotcom.wordpress.com I found a manual for the xs1,xs2, tx650 that shows the cutters for the valves. There is a 45' 40mm cutter for intake,45' 34mm cutter for exhaust,65' 42mm cutter for intake and exhaust plus a seperate cutter for radius...
  3. KennyD77

    Valve Seat Cutters

    Neway cutters work nicely. The kits can have a breathtaking price but you could just get the cutting heads you need for your bike and it's not too bad. cylinderheadsupply.com is who I've bought from, very nice people and happen to be very close to me now, but not when I first used them.
  4. KennyD77

    Rewinding or Replacing the Alternator Rotor in the UK

    Never done that before.. (koff)
  5. KennyD77

    Stuck Ring

    Acetone and ATF 50-50 mix.I have a friend who swears by it to get old tractor motors unstuck. I'm also a fan of Kroil. Amazing stuff
  6. KennyD77

    An Adventure in Firsts: '83 XS650 Heritage Special Build/Rebuild

    As I remember, Barnett will custom make cables. At a shop I once worked at had a customer with a mid 60's Harley XLH. The tach drive came off the top of the points housing and the tach was a Smith's. Called Barnett, sent a sample , and got two cables (one for a spare) and the cost wasn't that bad.
  7. KennyD77

    freshening switch blocks

    Thanks Jim
  8. KennyD77

    freshening switch blocks

    Jim, what paint would you recommend for frame/ chainguard touch up? Need to spiff up a few spots on my bike.
  9. KennyD77

    Best Multimeter for working on bike

    I still use a Simpson 270, great meter and sometimes better than a Fluke. I also have a couple Flukes and also a test light which can be invaluable.
  10. KennyD77

    Other Bikes and Workshop Woes

    Hi there, I have two suggestions, first search around for Kroil penetrating oil. Not easy to find and not cheap it's the best I have ever used.Second, ATF and acetone mixed 50/50. I have a friend who's a tractor buff who swears by it. Said he's used it to unstick seized motors on tractors that...
  11. KennyD77

    LOCKDOWN REBUILDS XS 1 TX AND SPECIAL

    I agree with using the bushings on the swingarm. Harley sporsters used timken bearings in the swingarm and I've pulled the shocks off and had the swingarm stay right where it was due to the flat spots in the race.
  12. KennyD77

    Can anyone ID this?

    2nd gear on the 750's was a weak spot. I've never had a problem with mine, but I don't romp on it in 2nd. It was fixed on the 850 trans, which is a drop in replacement for the 750 trans.Keep an eye on the oil level. They have a tendency to blow oil out the crankcase vent. If you fall to low on...
  13. KennyD77

    Can anyone ID this?

  14. KennyD77

    1981 Yamaha XS650S - Project Bike #5

    If you can find 1/8 Left hand drill bits, a lot of times when you start to drill it will grab the plug and spin it right out. My two cents. Hope it works out for you.
  15. KennyD77

    Long distance trips

    Truth! I made several trips from E.Rutherford To St.Pete Fl on my '51 panhead. I felt I was doing good if I could maintain 50MPH average.
Back
Top