Search results

  1. OldskoolXS650

    1982 XS650 Pamco installed

    Ok so I unhooked the Pamco and hooked it back to stock ignition fired right up. If you read this Pete I need some warranty help. Thanks
  2. OldskoolXS650

    1982 XS650 Pamco installed

    Should I have the little black ignition box hooked up when running Pamco? When u install Pamco do you need to unhook anything ? I am having issues with my bike again it was running fine then started missing and would not accelerate then died. I checked voltage at battery 12.30volts check voltage...
  3. OldskoolXS650

    1982 XS650 Pamco installed

    We are back on the road problem solved just a ring terminal on the ignition that had broken off because it had been bent and I guess vibration knocked it off.
  4. OldskoolXS650

    1982 XS650 Pamco installed

    I think I figured it out I had a wire that broke off the ignition switch. I fixed it but my battery was low so I'm charging it now we will see what happens. Thanks for your help guys I'll let y'all know what happens.
  5. OldskoolXS650

    1982 XS650 Pamco installed

    Thanks Pete
  6. OldskoolXS650

    1982 XS650 Pamco installed

    Thanks Dirty Dog I will check it out as soon as I can.
  7. OldskoolXS650

    1982 XS650 Pamco installed

    Alright guys I need a little help to get my bike back on the road. I bought the Pamco with Eadvance and all parts to install on my bike. Upon the first start up it ran fine I went for my maiden run with new ignition and while riding it was as if someone had turned off the key it just died. I...
  8. OldskoolXS650

    Pamco Eadvance wiring need help

    Alright guys I am still having issue and need some help. Im starting to think that I have a different problem. I get the bike running and the right side is still firing harder than left. I have check cam chain tension,replaced valve adjusters and set them,had Oldskool rebuild carbs,install new...
  9. OldskoolXS650

    Pamco Eadvance wiring need help

    I just had Oldskool rebuild the carbs and I have checked compression it was 155 left and 160 right.
  10. OldskoolXS650

    Pamco Eadvance wiring need help

    Alright guys I got the Pamco on and it's working great but I still have a problem. I have checked the cam chain tension and installed new valve adjusters. What is happening is the left cylinder is not firing as good as the right side. I hooked the bike to the manometer I made and I can sync the...
  11. OldskoolXS650

    Pamco Eadvance wiring need help

    Thanks Leo.
  12. OldskoolXS650

    Pamco Eadvance wiring need help

    I am installing the Pamco with E advance on my 1981 Xs650 I have read the instructions on Pete's site but can't understand everything. I put the new coil on (17-6903) how does the wiring go do I use the original wiring that ran to the coil also. Any help would be appreciated on proper way to...
  13. OldskoolXS650

    BS34 Troubleshooting

    Ok so sent the carbs to Oldskool and he rebuild them I put them back on the bike and the left side was back firing. I got the manometer out and synced carb. I get the fluid the same level and bump the throttle the fluid rises on the left side and after idling for a while evens back out. Also the...
  14. OldskoolXS650

    What have you done to your XS today?

    I installed a new tail light and redone the wiring. Now I have a tail light and a brake light. :thumbsup:
  15. OldskoolXS650

    BS34 Troubleshooting

    Paulrxs650 I had the left cylinder idle screw on the shaft all the way in not the mixture. The mixture was at three turns out and right cylinder was dead by means of spark tester. The bike would start but you have to keep the throttle on if you let off the bike would not run or idle. Today I...
  16. OldskoolXS650

    BS34 Troubleshooting

    I tried the dead cylinder method and the bike won't even idle on the left carb. I even turned the idle screw all the way in and it dies unless you give it a little throttle. What controls the idle circuit?
  17. OldskoolXS650

    BS34 Troubleshooting

    I set both mix screws at 3 turns out and I have not synced carbs yet. I need to build a manometer. Thanks for the help I'll keep at it with fingers crossed.
  18. OldskoolXS650

    BS34 Troubleshooting

    I took the carb apart and cleaned them today. the float level was good. I put on new carb holders and new plugs. The left side is still not idling correct but seem to do better when you blip the throttle. I took it for a test drive on deceleration it back fires. Any ideas?
  19. OldskoolXS650

    My garage has become a shop and i love it!

    Nice work man!!!!!
  20. OldskoolXS650

    BS34 Troubleshooting

    I installed new plugs and carb holders today. I also went thru the carbs I found that one mix screw still had the old washer and Oring stuck in it with the new. I'll keep y'all posted.
Back
Top