Search results

I need a Stator, Rotor, and all the hardware as well (woodruf key, nuts, and washers etc). If you have one please PM me and we can discuss.

Titles says it, have a 2 into 1 intake with a VM 36 carb/throttle cable/filter from Joe Wiseguy. PM me your offers.

So i bought the 8 pack clutch kit from ironheart cycles which came with the following: 8 new clutch plates 1 new steel plate springs/retainers thrust bearing/washer I have a 79 2f so it was a pretty easy install. I measured my old steel plates at 2.96-2.98, slapped it all together and for the...

So my neighbor ran my bike over while I was at work, insurance company totaled it out, the shop told me my tubes forks/tubes were fine but the triple trees were bent at the pinch bolts. So i got some new triples from gggGary put em in and everything looks straight. Riding around at low speeds...

Looking for 35mm triple trees, lower and top. Lemme know if ya got a pair willing to part with.

I'm taking a trip from Chicago to Charleston WV and I made it here but it took 16 hours. The trip started out great, made the first 300 miles cruising along at 75mph. But I stopped for gas, had myself a sandwich and drink and then kept going and everything just went to crap. My acceleration...

I've ordered Part # 12-0044, looks exactly like the one im replacing except that the plunger on the end is copper instead of plastic. After spending about an hour and a half wondering why i keep blowing fuses i find out that its shorting out on the end of my brake lever as soon as i start my...

Need a speedo cable, if anyone has one shoot me a pm or post here. Thanks.

Looking for a pair of stock special 2f pullbacks, if you have em sour me a pm.

I'm using my phone to type this and I'm on the road right now on a trip to Florida from Chicago and ive hit a problem. rephased engine, hughs pma, i know i have the carbs dialed in the plugs were good when i pulled em. got into Nashville yesterday evening and I started to lose power. so...

so i believe my regulator is broken. I've tested the diodes in both directions on the rectifier and they're what they should be. I started the bike using a power supply I own and I can turn the supply off after 30 seconds and it will stay running but when I measure the voltage coming from the...

Anyone off the top of their head know how many cam rotations there are in order to get 1 complete crank rotation? The engine in question is rephased, with a pamco ignition, i'm trying to make a digital speedometer using the pamcos 12 to 6v signal when it sparks. I've got the micro controller to...

I purchased a HHB PMA kit a little over a year back and wired it up per his instructions, haven't had an electrical problem till now. I was riding along the highway and my bike cuts off and loses all power so i quickly have to make it from the left lane to the right without getting crushed by...

I've put about 2k miles on this rephased engine and I've had little to no problems with the bike. But today out of no where the kicker started to freeze as I would try to kick it. when I try to kick it, it just becomes incredibly hard, like it freezes and the gears aren't matching inside to...

I just rebuilt this engine and I'm getting oil leaking at the chain sprocket from the transmission. I took the sprocket off and started it up to see if it was my seal and its not. The oil is coming from where the sprocket slides on not the transmission. Did I mess something up putting this back...

I've rebuilt my carbs (bs38's), gone through all ranges of jets from stock to lowest andI'm 95% sure my rich problem is coming from the damn oring that goes around the emulsion tube. I've ordered the viton mccar master orings everyone suggests, when I went to put them on and put the tube in it...

I've got a complete Vesrah gasket kit (VG-282 for xs650) and ive got the engine pretty much in pieces. My question is, what are these small o-rings for? i know the orange are for piston, and the four black are for the valve covers, 2 are for the breaker plates, but the rest of these, i never saw...

I've torn apart the cases and sent my crank/cam off to hugh for a rephase and got the news that the connecting rods were crap and needed replaced. Now i'm looking at the transmission gears and am wondering the same about them. The connecting rods had moisture damage and i'm wondering if the...

I have two sets of xs650 points, they are both off of 79 xs650 special II f. Send me a PM or make an offer here.

Shoot me a pm with your offer, I won't know shipping till i go to the post office. 35mm stock forks: SOLD Two pairs of points ignitions: you'll probably want to put new brushes on them. Stock gas tank: SOLD Set of front/rear turn signals: all the bolts to hook them right up...