Search results

  1. Kimura97

    Bike won’t rev past idle

    My bike started blogging down and will not rev much past idle. I have minkuni Vm34 with 190 jets and velocity stacks. The bike was running fine then started blogging down on throttle. I took the carbs off and cleaned them with carb cleaner and compressed air and it ran fine, then started...
  2. Kimura97

    Xs650 not starting

    coil between power and trigger terminal is reading 2.5ohm and between both the plug wires is reading 15.5k ohm so I’m thinking the coil is alright.
  3. Kimura97

    Xs650 not starting

    I have a 83 xs650 with a pmco/pma/sparx cap. The bike was running great then one day it just stopped and I cannot start it. I put a spark tester on the plug and it has no spark. The fuse panel is getting power because then I pull a fuse the light indicates on, for an open in the system. Do I...
  4. Kimura97

    ADLERT tires?!?

    I think I'm going to go with the Coker front as well. I have a 21x2.15 rim on the front.. im thinking the 21x3 tire might bubble out a little more then I want. should I go with the 21x2.75? what yall think? or is the 3 safer? MHMMMMM
  5. Kimura97

    ADLERT tires?!?

    no takers?!
  6. Kimura97

    ADLERT tires?!?

    Anyone heard of these new/ new to me tires? They match up perfectly with my firestone delux champ tires. I have 21x2.15 front wheel and having trouble finding a nice looking old tire. This Adlert is 21x3 so it should fit nice.. thoughts...
  7. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Finally got down the timing issue, one again had to go in and fine tune the carbs. The plate is pretty much centered with a little advance. Sorry for all the confusion I have been learning as I go, I used a battery to tune it because the voltage is still very high, as of now everything is...
  8. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Sorry guys, I'll try and be more specific with my post. After I hit it with the timing light again I will let you know. I just don't have enough time with my work schedule to dial everything in like I would like.
  9. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Getting so caught up with the carb issue I forgot to check the original voltage. Measured voltage around 10-12v at idle and 15.8 under some throttle...
  10. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    So after a day of reading up on the carbs I stepped down the pilot jet and lowered the needle one notch while keeping the original main jet. Timing is still off i feel, even after taking out the slack on the rod it's still almost all the way rotated clockwise. Little bit more fine tuning and I...
  11. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Good news I got it running, rough but running. It will only run with it almost all the way advanced. Still need to try and get a good baseline tune before I think about re jetting the carbs. Any reason why I would need it almost all the way advanced for it to run? Don't mind the mess with the...
  12. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    No I got the machined aluminum kind.
  13. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    As well I looked into the carb. Can see a lot of atomized fuel haze. I'll get on it tomorrow
  14. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Here she is by the way
  15. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    It's trying to start but requiring a lot of kicking. The timing is set to middle per the instructions. Definitely think it's a carb tuning issue
  16. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    As far as I'm tracking yes. http://www.nichecycle.com/ncs/mikuni/carb-kits/yamaha/ncs235-yamaha-xs650-70-79-vm34-carb-kit.html
  17. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Yea opened the drain plugs and fuel was coming out
  18. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    I reset the initial idle setting on the carbs. Got some backfire out the carbs
  19. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Sprayed some carb cleaner in it, wanted to run but died. Thinking I need to adjust the carbs?
  20. Kimura97

    Starting w/ pamco h/o ignition +e-advancer /pma

    Installed the new pamco as per instructions with new coil. Installed new minukni carbs with new lines filter and new gas. Tried starting with the battery only connected to the coil everything else to the pma unplugs, with the green wire to the pamco left in coil. Ran positive batt wire to red...
Back
Top