Search results

  1. J

    Minor front disc brake drag

    Along that train of thought would it be possible that new o-rings would take a bit of time to "break in" and start retracting after a rebuild? Just spit balling
  2. J

    Tach/speedo combo

    On the gps style, do you know if there are issues w signal loss in rural areas? I'd rather a bulletproof option but like the idea of less cables
  3. J

    Tach/speedo combo

    Has anyone tried a aftermarket tach /speedo on a bobber. Any reccomemdations.
  4. J

    gear shift pedal

    Correct me if I'm wrong. But the chain guard part behind the hand will need to be removed to check or access the c clip that retains the whole shaft from pushing in and not engaging the star gear thing on the other side?
  5. J

    Clutch/flywheel

    Thank you. I have not adjusted clutch cable yet. The play seemed a bit more than it should be.
  6. J

    Clutch/flywheel

    How much play is there w the back of the clutch/flywheel. I'm wondering if I need to add another washer.... Po had it apart so I did not see it removed. Been guessing and using the manual to try to reassemble. Let me know if this is normal play/slop. https://vimeo.com/166854566
  7. J

    Bad slide diaphragm symptoms

    I had to. Forgive me for being disruptive.
  8. J

    Bad slide diaphragm symptoms

    Pregnancy?
  9. J

    Head bolt/ studs

    I pulled them out and messed up a couple.
  10. J

    Can you paint capacitor (TCBros) for battery delete?

    How bout black duct tape
  11. J

    Head bolt/ studs

    Does any one know where to find head bolt studs. The ones that are 10-12" (ballpark). I checked all thru mikes xs with no luck.
  12. J

    What Brand of Valve Seals are Best?

    Following. Same question.
  13. J

    Custom title vs re-issue NC

    I'm trying to determine if it's easier to get a title for a custom bike (using the no title bike- creating a bobber and calling it a 2016) or doing the rediculous amount of work to get the title recovered. Synopsis. Bought basket case bike from a man who got it in an estate sale. Last owner...
  14. J

    One Man Engine Install - Is it possible?

    Tilt the engine, inside the frame. Reattach the upper bracket to the engine. Tie ratchet strap to top of engine. Then connect a come along to the strap and to roof rafter (at the other end). Ratchet and wiggle engine until it's free. A second person is helpful but not mandatory. Roll the bike...
  15. J

    Wanted - Seat XS1 XS1B or XS2

    I have an un torn 80/81 seat. Pm if your interested.
  16. J

    How to Remove Crankcase/Engine Studs?

    I've found that even with the stud remover and heat (map gas or propane) the studs get beaten up badly in the removal process. I wish I had left them in... Bc now I'm gona have to replace about half of them.
  17. J

    Yet another cam chain guide

    What is the first sign that it has come apart.... Noise or visual of oil? Following this thread, as I'm planning to get a new one from mikes.
  18. J

    Which Hardtail? (Living in Sweden)

    Also Hugh does the pma convert kits which are a good idea for the bobber plan.
  19. J

    Which Hardtail? (Living in Sweden)

    Factory metal works. Talk to Lucas. He was referred by Hugh from hughs hand built. Both guys in North Carolina. Lucas is in concord/ Salisbury nc and Hugh is in Asheville nc. Hugh can rephase your crank (YouTube him) and pamco Pete can work w you on converting the ignition to work w the rephase...
Back
Top