Search results

Mike XS is out-of-stock on his 2.45 Ohm dual output coils that need to run with his electronic ignition. Can I substitute a 2.2-3.0 Ohm dual output Harley coil from eBay until Mike gets them back in stock so I can get back to riding? Or maybe one of these (pricey) 3.0 Ohm Accel units...

Not so concerned with paint or interior rust, just no dents.

Replacing seat cover on my '77 and the clips that hold the trim piece are pretty rusted out. Anyone have a source for the rivet clips that hold trim to seat?

Hopefuly this is not too far off-topic, but I'm fitting a Radian swing arm to my XS and it's missing the chain pullers/tension adjusters & these are no longer available from Yamaha. Have had no success with eBay or local junkers. Does anyone know if there are other models/years chain adjusters...

I want to rattle-can paint my tank Kenny Roberts yellow over the winter. Any one know what Duplicolor yellow is a good match?

Aftermarket headers and exhaust means no more sidestand stopper. It just clangs against the frame when I put it up. Is there some sort of frame-mounted bumper I can install? Google shows lots of stuff for Harleys. Not sure what fits. Thanking you in advance

I'd like to replace my stock wiring harnesses but Mike's XS has been out of stock on the correct replacement for my bike months. Is there another vendor I might use? Thanks in advance!

My Heiden Tuning regulator/recitifier arrived & I'm attempting to install it. It's supposed to be plug & play into stock wiring harness. Heiden rectifier plug matched stock rectifier plug exactly. Same number of wires in same position into the harness plug. The Heiden regulator plug has two...

This unit looks like a simple plug & play installation but wondering where I should mount it for optimal cooling. It didn't come with instructions. Anyone have this unit & have some tips? thanks! Doug, San Francisco

Looking for a front disc (12" diameter) for a '77D roadster.

I'm setting up a dual-disc front end & want to cross drill the rotors before I do the install. Anyone know of a machine shop in No California (or in the Western US) that does cross drilling? I don't own a drill press or I would do myself. thanks, Doug San Francisco

I've ditched my instrument cluster for mini gauges on my '77D. There's now no place to mount my stock ignition switch so I've sourced a steering crown & switch from an 80's model XS that has mounting bungs for a switch. Wiring looks different across the switch plugs however. My current switch...

Replacing & relocating my '77D ignition switch with a 3-position switch from TC Bros. Back of TC switch has 3 poles labeled: B ST G My stock switch has: 1 - red wire 1 - red/yellow wire 1 - blue wire 1 - yellow wire What goes where? Photo attached. Thanks in advance!

I'm running new mini gauges (NOT the ones with the indicator LEDs from MikeXS) and I'd like to wire up a neutral light that I've mounted inside headlight shell. Just a small green LED (see attached photo) with red/black wires. Wiring diagram shows original wires for neutral lightbulb as...

I'm ditching the Battlestar Galactica-style instrument cluster for mini gauges. Not quite sure what to do with ignition switch. I would like to keep near handlebars. Does someone make a plate that attaches to handlebar mounts that will work?

I found two of these ceramic bits taped to the rear frame rail on my XS from a previous owner. Are they associated with the fancy LED taillight he put on? What they heck are they?

I like to adjust idle on the fly on my '77D and I'm tired of using a screw driver. Know if anyone makes a nice big knurled idle adjustment screw for the BS38 Mikunis so I can make adjustments with gloves on? Alternatively, does anyone know the size/pitch of this screw?

These were mounted on a ’77 XS that I just purchased. PO said he paid close to $400 for them. Aluminum with rubber-mounted pegs. Look solidly built & work well. Wear mark noted in photo from a tip over & and there is a very slight bend in shifter lever. Would love to get $200 (+ shipping) so I...