Search results

hi guys have my 72 xs2 finished and for sale open to good offers as u can see this was a total ground up restoration all new crank brgs factory oem crank balnced at gord bush racing all wheel brgs abd steering head brgs new tires tubes it goes on and on new top end ready to roll nothing over...

hi guys i have 72 xs2 and my clutch side bar switch is toast would any one have a complete assembly for sale or would anyone know if i can use one the switches mikes xs sells that doesnt have the light on off option thanks for your help in advance gravelman

howdy guys gravelman here we where just rebuilding my 72 xs2 motor and noticed a litlle crank wobble . i live in huntsville ontario and was wondering if anyone could recomend a crank shop to true weld balance my crank gta would be good any help welcome or anywhere in southern ontario thanks...

howdy guys i have a 1972 xs2 with the stock carbs on as far as i know.mine has only one choke on left side if that helps with a rubber crosover tube to other side .now when itook carb apart for cleaning i took the choke housing off on the left side which had a gasket on that got torn .so i...

howdy guys i am in the middle of installing my pamco ign .amd i have the ultimate coil .and i was reding the instrutions on wiring it says to hook the red wire on the positive side of the coil and i have searched high and low for the marks but thereisnt any on the coil has anyone seen this or is...

howdy guys i have a question on valve lash does anyone with the early 70 -73 actually run 006 int and 0012 ext lash .iwas reading the specs and i think thats a little wide myself and wuld probly be real noisy i have been running 004 -and 006 .and the bike performs well with not to much tappet...

hi guys i just finished my xs2 as a rolling chassis no motor yet so i wired up the battery and hokked up all wires in headlight pot and got nothing .my question is can u check it in this manner or dou need the main harness from motor plugged in thanks joe

hi guys gravelman here.well i found something intristing on my 77 650 today.i was having problems trying to get the bike to run correctly wouldnt idle very good and broke down on the midrange .anyways i tore the carbs apart clened and cleaned then i checked all my jetting and needles which was...

hi guys i have a question on my pamco ign i just got .i went on the website for my directions which i found ok .but the part that confuses me is when u install ur ign it says nothing on where ur motor position is .like on my boyer i have on my other 650 it tells u to have the motor on tdc mark...

hi guys i just recieved my pamco ign that has been on back order for a while .i ordered the 14-0911 kit i believe 151 bux anyways in the 650 direct site they show that kit with the green monster coils if iam seeing it rite but i got the black coil with side posts has anyone else had this happen...

hi guys i just got to the point of installing front end on my bike could anyone tell me if theres a spec for setting the fall off on front end. should it be done with front wheel on? or can u set it with just the fork assembly thanks joe

here some piks of my new ride keep the oters company lol

hi guys Joe here i have a question. took my oild pump apart today and i noticed the 2 black index markes . on the drive cogs where faceing away from the way of from the way u view .i mean backwards u would think they would be facing out .anyone know if it makes a difference .thats the way it...

hi guys joe here.i just tore down xs2 motor and found one bad crank bearing drive side ball type.Any suggestions on finding one .Iknow mikes has them made in tiwhan .any netter stuff around thanks joe

hi guys joe here just want ur guys take on these oil drain plugs from 650 direct or mikes k itighten mine up with my yamha factory wrench with its extenshion till i cant get anymore out of it .ok then u go and check it 2 days later after just maybe few min running than kool for couple days...

hi guys joe here i have a question and i cant seem to find no info .k i have a 71 xs1 b which i recntly got anyways i was just setting it up and noticed that it has what i believe to be 2 vacaum port fittings that are joined together i think anyways.on my 72 it doesnt have that .anyways on my 72...

howdy guys joe here i got a bit more work done today on my xs2 heres some more piks

hi guys joe here i have a question to ask.u know ur sump filter cover if ur looking at it from under the bike from the throttle side there is a half rounf kinda casting which look like it had a plug in it a round looking out fit and iam getting a small leak from there has any one had an issue...

some cleaning up on my xs1 just got it cpl weeks ago oh the disk is from xs2

hi guys joe here i just took some bigger piks the last ones where small cheers joe