Search results

Pending sale to Johnnny13 Up for sale is my 1981 Yamaha XS650 Hard tail conversion. It runs strong, and has many new parts. I have not had as much time as I thought I would to ride the bike so its got to go. The bike does run, and you can hear it run in person. No test rides or funny stuff...

Currently I have my bike jetted for the 90 degree weather but lately its reaching highs of 50's and maybe 60's. Well my bike has developed idle issues as well as 1/8-1/4 throttle flat spot. Here's a rundown of what I've got 74 TX 650 motor Pamco Ignition (original) Dynatek Coil NGK plugs...

1980 XS650 with PMA (HHB) Pamco Original conversion Dynatek DC1-3 Coil Yuasa YTX12-BS Battery Bike has ran just fine for a full season, just went to take it out and no spark. Here's what I've gathered from troubleshooting and checking everything over the last 2 days. Battery 12.4 VDC Coil...

Clean up time FS: 19 inch OMARS rear wheel kit Kit includes CNC billet 6160 and 7075 aluminum components: [1] Sprocket side (left) wheel spacer [1] Brake side (right) wheel spacer [1] Center bearing spacer for 20mm axle [1] Sprocket adapter – aluminum [1] Disc adapter – aluminum [3]...

Title says it all. Please nothing scared or bent. Shipping via USPS mail is OK!

Up for sale is the stator off my 80xs. It tests good at 5.5 ohms between the rings via my fluke 87. It was removed with a proper stator removal tool so you don't have to worry about anything! $30 shipped. I also have the alternator and brush's that came off the same bike that I'll throw in...

Well I'm trying to clean up some small oil leaks and I'm wondering if its possible to swap the Drain plug crush washers with out draining the oil?! I know the clutch cover gasket can be changed with out draining it by tipping the bike on its side but I've got a feeling this is a no go on the...

Anyone have a Pamco Ignition they are looking to unload? I would take the original style, or even one with an E-Advance. Stock engine only please I also am looking for an upper/top brake line that connects from the Master Cylinder and runs down to the middle of the fork to the brake manifold...

Picked up a project that I'm turning into a cafe. Got some things for sale. All these first parts are off an 80 XS650GS TCI box $60 Wiring Harness $35 (Main Harness will include all sensors n relays not sure of the working condition of everything, bike wasn't running when I got it, more...

Looking for a float bowl for a 74-75 XS/TX 650. As long as it is in good condition. Would like if it had the stock sized pilot jet too but if not that's fine as long as the pilot is free and removable. Lmk if you have anything!!

Can anyone ID this carburetor? I'm trying to rebuild them and see that the model breakdown is not as simple as the BS34. The two were not linked together, both had separate cable pulls. I think it's the 70-75 according to the rebuild guide but then when on 650central there's kits with in...

I'm working with a 1973 tx650 motor that has points, ATU, battery, I am not charging the battery when riding around or when reving above 3k. The bike has just an early style 5 wire regulator with no tci. The bike is a kick start only and starts on first or second kick no problem. It even will...

77-84 Right Side Caliper with new Piston, decided I wanted to go to a polished set up. Will include Pads as well. $35 shipped via USPS - Used Part #16-4659 Mirror Adapter Set - 8mm to 10mm, Set steps up 8mm. RH thread mirror holes up to the more common 10mm Set includes 1pc with 10mm RH female...

Im working on a 81 xs650, all stock charging system/ignition. I have a relocated fuse box inside a fake oil tank under the seat. When going to adjust the Carb Sync screw in the middle, I am noticing a spark/arcing that will jump from the screw driver to the frame when I am on the carb sync...

Im looking for any or all of the front brake components for an 81' XS650.. I need the Caliper, Rotor, Pads, Hardware, Line, Master Cylinder, and Lever.. So, ANYTHING from the front breaking assembly. I am also looking for any front fender, stock, aftermarket, or what ever, with any mounting...