Search results

http://southjersey.craigslist.org/mcy/4142644513.html See it running here: looking to get 2800.00 bike is rideable now and needs very little to be 100% done.

very cool. What is the headlight from?

I had a problem with using a cap from my 650 tank on a 750 tank. They apparently had the same p/n but the bar thats welded to the tank was welded in a dif location. I wound up having to drill out the spot weld and relocate the hinge on the tank. Just an idea of what might be wrong.

Leo I have the right side cover off. I can move the plates by hand they dont seem stuck to anything. Everything looks clean in there? I pulled the clutch off I am going to clean every thing up and put it all back together and see if that helps.

This is a project bike I took over. Ive had it for about a year but only heard the motor run for the first time a week ago. Ive yet to ride it because the clutch will not engage. If I mash the thing into a gear and pull the clutch I cant move the bike. Then I have to try to find neutral again to...

Ran out to harbour freight picked some up. They were just the right size to fit in there. Stuck one on the clutch rod and stuck it in there... Pulled both balls out! Great idea! thanks Thanks Damien but these rare earth daddies worked great.

Do exactly what this says and you will have no problems. If you plan on reusing the factory connector you might have to move some of the wires around on the connector.

Okay so I am trying to get a project bike together I bought as a basket case. I cant get the trans to go into neutral or even free spin if I pull the clutch. Has new cable and ive adjusted it a few times as described on here. It didnt have the outer ball installed when I got it. I put on in and...

okay so checking my wiring. My stator wiring has actually 5 white wires. but with one with green cloth covering and one with black cloth cover. I am assuming green to green and black to red. I also had to repin the 6 pin connector supplied with the replacement reg/rect. Actually reading...

Good thread was just about to ask this same question.

Thanks. I doubt my xs will ever go 112. I found these sites they are good references. http://www.cb450stuff.com/tires/ http://www.steelthundercc.com/tiresizes.html

Im liking the look of this "Avon Rear SM Mark II 4.00S-18 Blackwall Tire - 1646801" https://www.denniskirk.com/avon/rear-sm-mark-ii-4-00s-18-blackwall-tire.p641004.prd/641004.sku What does 4.00 translate as far as 110/90 120/90 Also like the Avon Front Speedmaster Rib 3.50S-19 Blackwall Tire -...

Im running grips for a bmx bike made by vans, they look like the vans shoes soles. Average comfort but look rad.

What size tire is that in the front? I guess shinko doesnt make a tire like your rear in 18" Also where is a good place to shop for them?

I like the look of this tire/wheel combo. What sizes do you think they are?

So I am finishing up a rigid xs build. Bike has the 19/18" alloy spoked wheels. I am having trouble visualizing what size tires to run on it. It is also holding up the final placement of my rear fender. Tires now are 100/90-19 and 110/90-18 Bike is nothing special, run of the mill...

what size wheels and tires are you running? I like that look alot.

Okay so I hooked everything up I think the same as the diagram shows. Bike fired up first kick. Lights all seem to work as designed. I don't think the alt Is charging tho. A meter on the battery while Erving Shows the voltage to drop. I also did a slap test and got nothing. As far as I know the...

Okay so that isn't anything I need to actually Wire to anything? They I assume are connected inside there somewhere because they disappear until they come out with the pigtail on the harness

Okay so I am using this diagram as my guide for my wiring. I have a few issues with it jiving up with my factory harness tho. Mainly I have a brown wire coming from my alternator and from my Rec/reg. where does the one from the alt go? And what is that little box with the Green and brown wires...