Search results

  1. L

    Carbs: Before I dig in

    I have read the guides, i have searched the interwebs... but I would like some guidance / thoughts. 81 XS-650, BS34's stock main 132.5, stock pilot 42.5, but Needle Jet - 336 YO, and Jet Needle - 5IX11. also stock air jet of 135 and 2 1/2 turns out mix screw. float bowl height 21mm +-. AND i...
  2. L

    FED UP, right side wont fire

    Hey guys, im a bit a wits end.. Hours and days just trying to get the right side to fire. 79 xs, 120 psi both cyl Valves checked Chain tension checked Points gapped Carbs rebuilt and tested 3 sets which work on other bikes just fine I have the pma on it, so i cant tell when its...
  3. L

    Throttle Plate

    Hi Guys, i have SEARCHED and searched all over the interweb. I cannot find a new set of Throttle Plates for my BS34's. I had to force them out of the shaft and on doing so nicked it a bit. nothing major but i would rather get new ones. Anyone have a spot i can find them or have some laying around?
  4. L

    Needle / Needle jet

    Ok, i need some help here b/c i dont want to buy everything and all of a sudden im F'ed at the end. I have a set of 81 carbs, BS34's. I am going to be redoing the carbs and hopefully everything is stock , BUT i am stomped on this 1 part since the needle is nowhere to be found.. IF i...
  5. L

    Ive had enough!frustrated

    At this point i have one through everything 5 times wth!? Setup: 1982 xs650 Using a capacitor , no battery . Volt is good when on Pamco + e advance unit Pma Vm34s tuned New plugs At first it was turning on and the bikes were the dame ones from another xs but it aounded 600000 times louder...
  6. L

    Rect/ Reg

    Guys qq.. I am seeing some diff Diags all over the place i just want to confirm.. i look at this one http://www.xs650chopper.com/2009/09/regulatorrectifier-combo-with-points-wiring-diagram/ and it shows that the Black From the Stator + The Org from the Rect/ Reg are suppose to goto...
  7. L

    How to remove bolts?

    Hey guys, since im going to powder coat the engine.. im trying to remove the bolts from the top end, mid and cyl. BUT i cant remove the bolts, how do i ? which tool can i use.. ex: the exhaust bolt, valve cover bolts etc.. thanks!
  8. L

    Fork Swap question

    Hey guys, i need to know if the 79 forks will fit the 71 triple tree. Right now we have the 71 xs650 but with the small top end break caliper. i want to upgrade to the bigger caliper, that sits to the back side of the fork. will i also be able to keep the stock 71 wheel axle, and the...
  9. L

    GEt spark, got gas, not starting!

    New build, engine was working. Integrated rect and reg, got spark just fine wires are all good. Carbs are fresh but wont start. Im going to throw bike out the window. And not to mention grindin noise from starter gear!!!!
  10. L

    Coils?

    Hey guys i have org and brwn on my coils for the points version engine.. Which is neg? Org right?
  11. L

    Difference?

    Hey guys, how big of a difference is the XS650 engine to the TX650 engine? I am about to purchase parts for the XS650 but i THINK if im correct its a TX650 motor. if its the same then i will go ahead and press process order!
  12. L

    Need a Diag for wiring..

    3 Point ignition key i have the Reg/ Rect. that has 7 wires coming out of it for the points version this one http://www.mikesxs.net/product/24-2089.html now, i have 3 Yellow, that will goto the stator i have 1 green, 1 red, 1 orange, 1 blue. where do i connect each thing? what i dont get...
  13. L

    Pamco + Integrated Regulator + Rect + New Charging System

    Hey Guys, im on here b/c im doing some work for a friends bike... He installed the following Pamco New Charging system Integrated Reg. and Rect no kill switch -> uses key as kill switch to turn off bike (with old ignition system) His key Switch is a 3 Prong switch. which if i looked...
  14. L

    Hydraulic to Cable clutch

    hey Guys i am doing a search for a friend and came up with nothing. basically b/c people go the other way around. does anyone have a how to convert from hydraulic to cable clutch on a xs650 1979 bike? thanks in advance!
Back
Top