Search results

Wingman1946 - are you aware that this for-sale ad was posted in February of 2012? It has been 4 years since then, and I don't have any XS650 parts anymore... nor do I even have the bike! :eek: I can't knock ya too hard since I never deleted this thread or marked it as sold (my fault), but if...

I have the type of coil you are looking for, with the leads coming out of the end (people normally face them forward). It is BRAND NEW, with NGK plug caps designed for it. Never used, never installed the caps. Ready for installation on you bike, $40 shipped for the works. Send me a PM I...

Interested in the rear brake pedal(s). Are all these created equal? I need it to fit my '81 splines on the pivot shaft. If so send me a PM with the price, shipped to Northwest Iowa zip 51360. Thanks! Logan

Still ready to send $20 via PayPal. PM me your address, thanks! Logan

Is it safe to assume that Hugh's PMA system is grounded simply by being installed on the engine? I.e. the nut that holds the flywheel onto the crankshaft is grounding it? Obviously you cannot run a wire because the flywheel is spinning, so it would only make sense. :shrug: Logan

I'll take it of nobody else has yet. PM me your PayPal address where I can send $$ to. Thanks. :thumbsup: Logan

Got one! You know who you are, thank you very much! :thumbsup:

Traded my set of spoked wheels for aluminum mag wheels 16"/19" and seem to have a fitting left side(chain-side) spacer but don't have the right hand one. It's a disc brake wheel, so I have the caliper holder also on he axle. TC hardtail, plenty of 3/4" washers to fill in the chain adjusters...

PM sent. Logan

Im in northwest IA, spirit lake/Okoboji area. I went to Iowa State in Ames so I know right here you're at. Shocks are kayaba standard length, but they're adjustable so it depends on how you measure them. I'd be willing to give you a heck of a deal on frame and any other parts you like since...

I have two engines in the shop, one that is going into my current build, and it has a 6-plate clutch in it. My spare engine has a 7-plate clutch inside. Can these be swapped directly with no supporting mods needed? I have a set of stronger (XS Performance) clutch springs and the socket-cap...

I got no offers on this stuff, so I threw the better items on eBay sold the Brembo setup for $33... Yes it would have worked on an XS with a custom caliper mount. TCI sold for $50 by itself. Still have most of the rest of it! I really just want to get rid of the stuff folks. If you're...

Have these ever come back in stock?

I have the whole works. Starting from brake lever/perch with master cylinder, brake hose (all connected), caliper, and rotor. Make me an offer, it's ready to be shipped out whenever I get payment. Thanks, Logan

What would you like for it just to sell? Shipped to 51360? I may have a bates 5-3/4" bobber headlight for trade, but it's brand new and usually go for a little more $$ than the engine stands do. Let me know, Logan

What part of Iowa are you in? I'm in the Northwest corner at Spirit Lake/Okoboji. I have two tanks both in good shape. One i just removed from a daily rider, clean as a bell inside, comes with the petcock, but I think it may have a very shallow dent in it. It's hard to tell really being a...

What are the dimensions of the lawn mower gas tank? And does it come with a cap? I need something for my bobber but do not care for the cookie cutter TC-Bros setup. Also is that a rear rotor in the pic? If so, is it smooth with no grooves or scoring? Logan

Update: Just purchased the Mikes XS one, since nobody had any alternatives to offer.. Side note, I would assume most garage-builders use the factory M/C's push rod and modify it to pull on the bellcrank lever? I do not have that part so I will be fabricating something from some hardware and...

Anyone know of a good aftermarket source for a bellcrank rear master cylinder, other than Mikes XS? I have no problem with his (its actually exactly what i need) but I can't find any even remotely like it on eBay or google. It's like they don't exist other than that one. Did any other bikes...

One of the best electrical threads I've ever read, my hat is off to you sir. On a side note, how much do you charge to build a brand new wiring harness for my XS? It would make my life easier! I'm off to eBay now to buy a nice solder gun and some wiring paraphernalia :thumbsup: