ignition coil

  1. B

    VAPE ignition Issues (and more)

    Hi first post apologies for any issues i haven't used a forum in forever. Ive just purchased an XS650 Herritage Special that was imported from the US and every fault i try to fix seems to multiply. When i purchased it the previous owner had fitted VAPE electronic ignition, MikesXS headers and...
  2. E

    XS850 - Coil resistance spec question

    Hi folks, I have a 1980 XS850SG (special) and I measured the ignition coil resistance to make sure I am in spec. The factory service manual spec calls for 2.75ohm on Primary and 7.9ohm on Secondary with 10% torelerance on both. Is this secondary spec considers a spark plug cap installed or...
  3. R

    Could my coil drain my battery, why?

    Hello, while I’m new to posting I am a veteran lurker. I have previously owned a 79 but unfortunately had to sell. I now own a rather troublesome 81. When I first bought the bike it was completely stock apart from the missing battery box. The original ignition black box was shot so I fiddled...
  4. B

    For Sale - Ignition Coil - 1.6 Ohm - High Output - TCI ignition for sale

    Ordered this and never used it. Ended up ordering a whole new vape ignition set. Retail: $41.97 + shipping. Ignition Coil - 1.6 Ohm - High Output - TCI ignition SKU: 17-6803 from Mikesxs https://www.mikesxs.net/yamaha-xs650-high-perf-dual-output-ignition-coil-oem-3g1-82310-60.html OBO +...
  5. ItsSamuelC

    Wiring Harness Hell.

    Hi, I recently bought a 79 XS650 Bobber. Somebody elses project they couldnt be bothered to finish etc. The wiring is atrocious and I have started to work my way through. I have fixed mistakes and repaired everything in their “wiring harness”, so everything is working, but its all still very...
  6. jasidok

    Igntion Coil Replacements

    I believe My ignition Coil is not working. Will this work as a replacement. https://www.euromotoelectrics.com/product-p/edl-coil3.0ohm.htm
  7. B Burdine97

    Spend the extra time, not the extra money.. TCI troubleshooting

    I am in the process of tuning my bike for my new pods and aftermarket exhaust. I told the honey Im heading out to the garage to do some work. Turned the fuel on, key switch on, choke on and started kicking. To my surprise, it didnt start! What the hell, I've been starting up the bike quite often...
  8. Sazbo

    Ultimate High Output Ignition Coil Dimensions

    Hi all, Does any one know the dimensions of Mikesxs Ultimate high output ignition coil, HxWxD and bolt hole to hole on center
  9. D

    Connect Spark Plug Wire to Ignition Coil?

    Hey everyone, I have a '72 XS2 that's been sitting in my garage for the last 23 years, and I want to get it out and onto the road. This will be my first project, so I've spent the last few months slowly doing research to figure out what I can before asking for help. Everything seems sound...
  10. E

    Extra wires that I don't know what to do with

    So I bought the basic high-output ignition setup from mikes Part #14-0911. All the hardware is installed I just need to wire everything. I have a 1975 xs650 which originally had 2 ignition coils that I replaced with 1. So now i'm left with some wires from the old coils and the old rotor/trigger...
  11. B

    PAMCO Ignition install troubles...HELP.

    Hey guys, So I bought a brand new pamcopete ignition and hughshandbuilt pma recently and just attempted to install the pamco today. I took the advance rod out and have the entire left side complete (sensor plate in place etc.). Now, I have a 1979 special...do i need to replace the right...
  12. X

    Ignition coils off other bikes

    Hey everyone, I have a 1980 with TCI ignition. My coil is bad and I need a temporary replacement ASAP. I found a local guy with a bunch of used ignition coils off of old bikes. He will sell me one for real cheap. What do I need to look up to know if the coil will work on an XS650? It...
Back
Top