pma

Happy Father's Day, Dudes. I have an 81 H that I have stripped down and rebuilt to the best of my ability. Did all the road worthy stuff like tires, suspension, brakes, cables, oil seals...including valve stem, chain, sprockets, etc. rode it for a thousand miles last year. Over the winter...

Hi all, I've presently got an RD350 PMA fitted to my bike but never got around to making timing marks on the flywheel. Can someone confirm that the only mark on the flywheel is for TDC? I'll also need to add timing marks to the engine cover. Please could someone confirm how many degrees...

So I'm headin down the highway and all of a sudden the bike loses power, lights go out, and I'm slowing down. Like a dummy I didn't have tools with me, so there wasn't much I could've done anyway. I pulled into a parking lot after coasting about 1/4 mile, and had hell starting the bike back up...

An '81 H Pamco EAdv and HHB PMA I have been getting no charging of my battery due to no output from the stator. The other day I took the rotor off and inspected it. It was clean as could be, but the unit had gotten hot enough to melt the logo off of the rotor. I took the stator off and...

Hey Guys, I have read every thread on this topic. I know advance from retard. I have installed an HHB PMA, Pamco with EAdv, shaft, bushings and the replacement rotor for the right side of the cam. I believe the pin was inserted in the right place at the top of the shaft rotation. I have...

piecing together my PMA swap and I got a 6 post stator and I am noticing that all the PMA swap kits use a 18 post stator. Whats the difference? Did I get the wrong banshee stator?

Have been pulling back and forth on ordering this for some time now and have been doing research on the forum looking at folks experiences but want to finally reach out for some extra guidance. I have found lots of suggestions to go with Hugh's PMA (as they stand behind their products /...

1982 xs special with a PMA from Hugh, Pamco ignition, and a small Sparx cap. I have a switch wired in to kill all the lighting when kicking the bike, and an on-off-on switch that controls the headlight (Bates style with h4 55 watt bulb). The bike fires up first kick, and can handle the lights...

Hey all, I have a 72 xs650 that has a PMA I pieced together years ago. No kits were available. I have a 5 wire reg rec combo feom Hugh if I remember correctly. Also running a pamco unit and small headlight taillight. Etc. I've tried the small cig box size batteries and killed cels in both. Now...

Hey all- I'm at my wits end with a charging issue with my '78 XS650. Here's the situation: I have an HHB PMA installed for a few years now, with a small SLA battery and no electric start. Charging system is super simple: just the PMA, SLA, and reg/rec. The issue is that batteries are...

Hey guys, This is my first post, but I've been using the threads to trouble shoot for a few months now. I know there are 1000+ threads on this issue, but I can't seem to find exactly the right answer. I've been doing some electrical work, and here's where I stand. 1. Upgraded to a PMA...

Hey folks. I'm swapping to Hugh's pma right now. And I'm out of ideas where to mount the Recifer. I thought about putting it on the little mount beside the upper motor mounts ( see picture) I know it'll get enough air. But what about the heat from the engine and the exhaust? Did anyone...

Hi all, I've just finished installing a home-spun RD350-based PMA. I believe it's the same rotor and stator as the US Banshee. It uses a 5 wire three-phase reg/reg with 3 yellow wires, a red and a black. The three yellow wires are connected to the three wires from the stator, the the black...

Sorry Mods if i posted this in the wrong section, still getting used to the forum, i meant for this to appear under Electrical as it pertains to the subject First of all i want to say i hate for this to be my first thread instead of a proper intro thread. I'm a long time lurker of this...

Hi ,I'm looking for some help on what size battery do I need with a new pma small as possible would be best.I changed the ignition for a electronic Boyer .:shrug: Posted via Mobile

Looking at an XS stator on eBay, a thought occurred to me, instead of powering the windings in the stator to create a magnetic field to induce current in the rotor windings to generate electricity, why not machine a rotor to replace the original and embed magnets in it to induce a current in...

Im doing some planning ahead for my upcoming build and I'm wondering if anyone has the actual physical dimensions of the rec/reg unit from Hugh's PMA kit? i just want to see where i can mount it on the bike. also, i know it needs to be air cooled (not mounted in a sealed box) but has anyone...

Okay, so I mentally masturbated this thing to death, and I'm finally buying (stealing) a bobber base from a coworker. (78 XS650) This site has turned the project into a money pit before I even get the thing titled. (Thanks Guys) Things I know I need to do include an ignition upgrade, a PMA...

I'm in the middle of replacing my old alternator with a PMA. I've got the regulator removed, but I'm not sure which is the rectifier? I know I've seen pictures of it, but my search is turning up nothing! Is what I've seen referred to as the 'relay' that has a similar look as the regulator, on...

G'day All, First post so go easy! I need a bit of help making a decision, I have had this battery box made up (in attachment), originally made to house a capacitor and switches, for a kickstart only PMA set up, Lights, indicators, running a new Pamco e-advance. But have recently had a...