tachometer

The face on my tach has come loose. The tiny screws that hold it in place have come loose, and are still inside the tach assembly. I am able to remove the tach assembley from the housing, but I cannot for the life of me figure out how to get the glass off so I can get in there and repair it. I...

Tachometer off my 77xs650 D. some wear and tear, all bolts with, works fine. one of the wires will need a new male or female end I don't remember. It's how I found it when I got the bike. Shipping cost is on the buyer because I'll ship wherever and some places cost more than others. Asking 35.00

Looking for speedometer/tachometer. Just need case and front glass piece so a broken instrument that is still round will do.

Came from an 82 heritage special, works perfect even back lighting. Also have tachometer cable if needed Shoot me an offer

In the slow process of customizing my '78 special with a tracker/scrambler look and I am trying to decide what gauges I want to run. Stock, mini, tach only..... etc.... I'd like to see some pictures of different gauge configurations people are running. I currently have a 5 3/4 headlight, but...

Hello guys i recently got a set of drag bars (27.5" Length, 0" Rise, 3.75" Pullback) from mikesxs for my 1981 special and began to install them. Everything was going great, I rerouted the clutch cable as seen on previous threads, I went to mount the master cylinder, but then began to run into...

Looking for a set of like-new speedo/tach for '70 - '72 XS. Need them for a '72 XS.

75 and up gauges, some standards and some specials. if asking please use odometer reading to ID the set you are talking about. That one set of special gauges is REALLY nice, shows 5K will include the better silk screen indicator panel below it. thinking $100 for those, others priced downwards...

The studs on my tachometer (the ones that hold it inside the housing, with small acorn nuts) are done. One was sheared off when I bought the bike and the others threads stripped when I was replacing the tach rubber. Are these permanently mounted or could I throw a pair of vice-grips on them or...

Hi guys. I'd appreciate your advice, especially if you have connected the yellow tachometer signal pickup wire from an Acewell Speedo/Tach unit to a stock 1981-1983 ignition coil. The manufacturer's instructions provide two options; 1) wrap the end of the yellow pickup wire around the spark...

Hey guys. I'm looking to get a 2.5" mini tach from dimecity. I'll be putting it on my stock '79 XS. Wondering what ratio to get? Looking to use the stock cable. Lemme know guys! Thanks! Garrett

I've got a 1978 XS650E and I'm trying to remove the tach cable from the right side engine case. I've looked at the various threads related to the removal and I'm still not getting it. It appears from some other posts that the top end of that knurled housing is supposed to have some threaded...

hey guys! recently the faceplate on the tach on my 80sg came loose,so i purchased a nice replacement.however it must be off of a newer model as it has 4 bulbs (high beam lite is one ) of course the wiring is different. original tach has two bulbs/3 wires-yellow, blue, and black (black to each...

Does anyone know of a source of a replacement for the little, black rubber cover that fits over the light bulb holder in the bottom of the tachometer? This is the small bulb that illuminates the tach dial at night (when the headlight is on). Recently, the rubber dried-out and is...

I got a new mini speedo and tach for my project from partsnmore (which by the way has these for $32 apiece). I got it all hooked up but I'm getting no reading on the tach. I was thinking the problem might be the tach drive on the bike, but unscrewed the cable on that end and put it in my drill...

I'm not going to run a tach. Can I take the worm gear out of the side cover, and put a cap in the top. Does someone make a cap for that?

I'm playing with my carbs and since I don't have a tachometer on the bike right now, I'm using my timing light to tell me the RPM. I'm assuming since xs650s have a wasted spark that I need to take the RPM it displays and divide them by two to get the proper engine speed?