For Sale - Yamaha XS750 Flattracker!

bt24

XS650 Addict
Messages
208
Reaction score
24
Points
18
Location
New Mexico
IMG_7700.JPG
IMG_7702.JPG
IMG_7705.JPG
IMG_7706.JPG
IMG_7703.JPG
IMG_7704.JPG


New Champion copy Yamaha 750 Twin for sale.
Fresh build, only break in time on new engine build, almost everything on this build is brand new.
$7,800. OBO plus shipping.
No trades, Possible delivery.

New Champion Yamaha XS750 Build/Parts sheet

New Chromoly tubing frame built in a Champion XS Yamaha Frame Jig.
New Tapered Steering Head Bearings
Rebuilt GSXR 750 forks & Triple clamps
New Vortex Johnny Murphree bend 1" taper bars
New Pro Taper Bar Risers
New Pro Taper grips
New Motion Pro Turbo Throttle
New Motion Pro 2 into 1 Throttle Cable
New Kill Button
New MSR Adjust on fly Clutch & Perch
New Clutch Cable
Works Rear Shocks 1/2 season old
New Excel Wheels 2.50X19" Front/ 2.50X19" Rear
New HD Stainless Spokes Front & Rear
New Maxxis Tires Front & Rear
New Barnes Hub Front
New Barnes Hub Knock Off Rear
New Streamline rear disc with New billit aluminum carrier
Nissin Brake Caliper with New Brake Pads
New Stainless Steel Braided Brake line
New Stainless Brake fitting
New Nissin Master Cycinder
New Billit Brake Pedal
New Billit Brake Ped/Mastr Cyl plate
New 520QR Tsubaki Chain
New Billit Axcel/Chain Adjusters
New Rear Axcel
New Swingarm bolt/bearings
New First Klass/Bates foot peg rubbers
New foot peg blades & mounts
New 750 Fiberglass Tank & Seatbase w/ Seat
New 90 degree K&L Fuel Petcocks w/New fuel line

New Engine parts list

New Billit Cam Covers
New Nuts & Bolts
New Billit Engine Mounts
New All Gaskets
New All Seals
New Reed Type PVC Valve Engine Breather
New Oil and Lower Oil Sump Filters
New Axcel 8.8 Coil Wires/Caps
New PVL Ignition and Coils
Norris 1/2 Mile Cam
New Tsubaki Cam Chain
New Cam Chain Guide
New Cam Chain Tensioner Pivot Arm Assembly
New EBC Clutch Plates Steel & Fiber
New HD Clutch Springs W/Allen bolts, aluminum spacers
New Clutch Thrust Bearings & Nuts
New Clutch Long Pushrod w/ Bearing
New Clutch Push Housing Assembly
New Kibblewhite Racing Springs w/Titanium Tops
New Wiesco Yamaha 750 Piston kit
New LA Sleeves
New RD 1mm over Exhaust Valves
New RD 1mm over Intake Valves
New Bronze Valve Guides
New 3 angle cut valve job
New hand ported Intake & Exhaust Head
New (2) 38mm Mikuni Round Slide Carbs
New (2) Billit carb Intakes
Jemco High Exhaust (Ceramic Coated)
New (2) K&N Air Filters
Stock Rods, Crank Bearings, Oil Pump, everything was checked for wear and runout.

Bryan Trippe
bryantrippe@msn.com
Albuquerque, NM. 87124
Cell: 505-400-7244
 
Lord, that is sweet!:cheers:
Is that a Champion swingarm? It looks way different than the Mule version - and it looks like the chain clears the shocks by a goodly amount.
GLWS.
 
Lord, that is sweet!:cheers:
Is that a Champion swingarm? It looks way different than the Mule version - and it looks like the chain clears the shocks by a goodly amount.
GLWS.
It's a Champion copy, the chain is fairly close to the shock but the photo does make it look far away though!
I'll have to take a look at Mules, are his a Champion copy also?
Thanks for looking,
Bryan
 
Very mice. Good luck with the sale. Is the case beveled for looks only? total loss ignition?

The case is beveled so you don't drag the case in the dirt. It's not a total loss system, there is no battery. It's a CDI system just like on a dirt bike, a PVL brand Ignition.

Also there is no flywheel, no kick starter or kick starter shaft, gear or spring.
It's a bump start, I have to put a remote starter hole where the flywheel is so you can use a remote starter to fire it off.
Thanks,
Bryan
 
Last edited:
Don't mean to crap in your thread...
but you asked.;)
I don't think the Mule is a copy of the champion, but it is similar. But yours looks like it has more shock to chain clearance. With the YSS shocks I was trying to run, it would have been an interference between shocks and chain in anything other than a static mode. I saw you have Works Shocks - I talked to them today, and they indicated they can provide a shock with an offset base. How much? I hope to find out tomorrow.
Love that left side cam cover.
Now back to a really cool XS for sale....:D
 
Knew that on the case, doesn't look like enough room for any flywheel, thats why I asked about total loss. Surprised you didn't move shift to right side? Regardless great looker.

The case is beveled so you don't drag the case in the dirt. It's not a total loss system, there is no battery. It's a CDI system just like on a dirt bike, a PVL brand Ignition.

Also there is no flywheel, no kick starter or kick starter shaft, gear or spring.
It's a bump start, I have to put a remote starter hole where the flywheel is so you can use a remote starter to fire it off.
Thanks,
Bryan
 
Don't mean to crap in your thread...
but you asked.;)
I don't think the Mule is a copy of the champion, but it is similar. But yours looks like it has more shock to chain clearance. With the YSS shocks I was trying to run, it would have been an interference between shocks and chain in anything other than a static mode. I saw you have Works Shocks - I talked to them today, and they indicated they can provide a shock with an offset base. How much? I hope to find out tomorrow.
Love that left side cam cover.
Now back to a really cool XS for sale....:D

No worries about the thread, I could take a picture at a different angle and measurements of the swingarm if that would help you with your shock selection? Just let me know.
Bryan
 
View attachment 95652 View attachment 95651 View attachment 95650 View attachment 95649 View attachment 95647 View attachment 95648

New Champion copy Yamaha 750 Twin for sale.
Fresh build, only break in time on new engine build, almost everything on this build is brand new.
$7,800. OBO plus shipping.
No trades, Possible delivery.

New Champion Yamaha XS750 Build/Parts sheet

New Chromoly tubing frame built in a Champion XS Yamaha Frame Jig.
New Tapered Steering Head Bearings
Rebuilt GSXR 750 forks & Triple clamps
New Vortex Johnny Murphree bend 1" taper bars
New Pro Taper Bar Risers
New Pro Taper grips
New Motion Pro Turbo Throttle
New Motion Pro 2 into 1 Throttle Cable
New Kill Button
New MSR Adjust on fly Clutch & Perch
New Clutch Cable
Works Rear Shocks 1/2 season old
New Excel Wheels 2.50X19" Front/ 2.50X19" Rear
New HD Stainless Spokes Front & Rear
New Maxxis Tires Front & Rear
New Barnes Hub Front
New Barnes Hub Knock Off Rear
New Streamline rear disc with New billit aluminum carrier
Nissin Brake Caliper with New Brake Pads
New Stainless Steel Braided Brake line
New Stainless Brake fitting
New Nissin Master Cycinder
New Billit Brake Pedal
New Billit Brake Ped/Mastr Cyl plate
New 520QR Tsubaki Chain
New Billit Axcel/Chain Adjusters
New Rear Axcel
New Swingarm bolt/bearings
New First Klass/Bates foot peg rubbers
New foot peg blades & mounts
New 750 Fiberglass Tank & Seatbase w/ Seat
New 90 degree K&L Fuel Petcocks w/New fuel line

New Engine parts list

New Billit Cam Covers
New Nuts & Bolts
New Billit Engine Mounts
New All Gaskets
New All Seals
New Reed Type PVC Valve Engine Breather
New Oil and Lower Oil Sump Filters
New Axcel 8.8 Coil Wires/Caps
New PVL Ignition and Coils
Norris 1/2 Mile Cam
New Tsubaki Cam Chain
New Cam Chain Guide
New Cam Chain Tensioner Pivot Arm Assembly
New EBC Clutch Plates Steel & Fiber
New HD Clutch Springs W/Allen bolts, aluminum spacers
New Clutch Thrust Bearings & Nuts
New Clutch Long Pushrod w/ Bearing
New Clutch Push Housing Assembly
New Kibblewhite Racing Springs w/Titanium Tops
New Wiesco Yamaha 750 Piston kit
New LA Sleeves
New RD 1mm over Exhaust Valves
New RD 1mm over Intake Valves
New Bronze Valve Guides
New 3 angle cut valve job
New hand ported Intake & Exhaust Head
New (2) 38mm Mikuni Round Slide Carbs
New (2) Billit carb Intakes
Jemco High Exhaust (Ceramic Coated)
New (2) K&N Air Filters
Stock Rods, Crank Bearings, Oil Pump, everything was checked for wear and runout.

Bryan Trippe
bryantrippe@msn.com
Albuquerque, NM. 87124
Cell: 505-400-7244
Sweet build brother!!
 
Back
Top