Tully

The reason bikes were ever baught for us as kids was my Dads bike he road in Texas before Vietnam. Honda 350 Scrambler. I believe that...

Does the engine have to be changed? Does it have to be rephased or can it be installed like just a set of new jugs and rings? Something...

Road the bike for a couple days. Bike seems to be working pretty hard. When I go a few miles and come to a stop it does not want to take...

The bike last night did feel like it took alot of throttle to get moving. Different than last ignition. Wonder if I should move the clip...

This is the small one I was talking about.

I was probably pretty damn close to that with the last ignition I was running.

I will put the degree wheel on it and make sure it is advancing to the 35° mark. Many thanks to you gentlemen!

Makes sense to me. At the pump here I have the choice of 87 and 91 octane. Ive been runnimg 91 in the bike. The Mikes XS that gave many...

My niece and my bike tonight.

Over 300 hours. I know its a bobber. But its what Ive wanted for many years just couldnt afford one so I built it instead.

Not on the top needle slot. I have 2 open slots below where my needle sits. I moved it down before I found the leaking head gasket.

Is the static timing not a good way to go?

I do have a timing and I sure will do that.

The bike was charging. But I still installed my 12volt 5ah battery. I found a small one mentioned earlier the size of a cig pack. But...

15 mile trip to town and sat for an hour and 15 back.

I was able to get bike running. This evening I was able to ride to town and back 30 miles. Very happy Guy tonight. 🙂

6 mile ride are these ok?

last evening I took point plate off off bike. Unwired coils and points. Rewired all back together. Than was able to static time the...

Light never shuts off ever

No matter what happens points open points closed constant power to them at all times!

Could the engine have spun fast enough to move the point after the pin fell out?

Brand new points. Just installed. Will regap and adjust accordingly.

Well i figured out how part of it happens. Big nut on right side of head came loose pin fell out knocked timing out. Reinstalled pin and...

When to check timing chain amd valve adjustment. All seemed good. To spec. When I went to to check timing static timing the light turns...

I sprayed around the intake boots and carbs before around the head. The rpms reved when sprayed where head meets jug under the spark plug.

Baught new compression tested.

This is the other motor. Kick not electric start was 120 per side after I retorqued head. But it wasnt the fastests kicks. Put in new...

Bad head gasket guys. Or need to retorque. Spray around head with something I probably shouldnt have. Bike RPMs went high.

The specs I read having brass floats at 27mm seem like there would need to be a bit of fuel in bowls to shut off the gas flow. If I...

I can run my starter off a battery anf some cables.

Everything in pis what I have. I will try those changes.

I am also going to buy new plugs today. Is there a certain plug I should buy? Factory 77 points and coil.

Sorry all I did run the needles to the kit. I replaced back to needle from kit when I synched carbs

This is the kit purchased and because I ran pod filters and straight pipes I used the biggest main and the biggest pilot. I was also...

I also have the jet kit from mikesxs in the carbs. I am running at this time the biggest main and idle jet they had in the kit. Odd...

Also after setting float height. When turn fuel back on i have to tap on carbs to get the fuel to stop running out of the carbs. I dont...

I need to retract last 3 posts the compression tester dont even read a lb. on a lawn mower engine. Might be junk.

oil in cylinders did not make a change.

I also only have a kick start.

Either side of the engine has no compression at all 30Lbs