Search results

  1. sweatybetty89

    So it begins.....

    It was sucking air on my boots and since used some gasket maker along with the gasket to stop that. Hit it with starting fluid and had no problem. Its like when I turn my air screw I get no change. It will idle okay and as soon as I take off on it it feels like it's still sucking air but it's...
  2. sweatybetty89

    So it begins.....

    Link is not going any where
  3. sweatybetty89

    So it begins.....

    Any advice on jets in vm34 carbs on 77d with aftermarket cone exhaust and uni pods. Currently 25 pilot. 180 mains. Not running great idle is shit. And mid is not to great either.
  4. sweatybetty89

    dying issue

    Well got the new carb put on and it is running like shit. It's not dying but it is running like shit. It starts to bog out when I start to reach my rpms at my shift point. Idles fine. Starts jetting?
  5. sweatybetty89

    dying issue

    If they were that badly out of sync would this not cause a similar issue?
  6. sweatybetty89

    dying issue

    So went and look a lil closer at my carbs today and find that they are not the same carbs at all. I guess they sent me a vm 34 180 main jet and a vm 32 140 main. I believe this very well may have some thing to do with the poor performance of my bike
  7. sweatybetty89

    dying issue

    I did hear it sucking air out of though the gas cap so vapor lock could be a issue but its been doing it even after taking the gas cap off
  8. sweatybetty89

    dying issue

    so i get the bike up to speed about 3rd or 4th gear and when down shifting i loose power and the bike dies. It is short and abrupt. almost like a clogged carb issue. i took them off to clean them and there was some gunk in them i recently cleaned out my tank and there was a lot of crud in it...
  9. sweatybetty89

    So it begins.....

    So today got on the bike rode out on the highway got into 3/4 gear and when I came to light and down shifted it list bower and died. The bike continued to do this all day. Took my carbs off and cleaned them. Still doing it. There was sediment in the carbs. Probably came from the tank I cleaned...
  10. sweatybetty89

    So it begins.....

    i think that they may already have been stretched. this winter they are comming out and getting replaced. what any one have any good tricks on flattening the surface of the bottom case. and they are at 35 and it is not leaking so idk.
  11. sweatybetty89

    So it begins.....

    so I got thre bolts torqued down to 32 lb on the big bolts and the others to spec. I am still getting a lil drip nothing crazy but still there. now i can go tighter correct? and would using a thicker motor oil be a option as well? I am using 10W/40 i believe now. what would be another option?
  12. sweatybetty89

    So it begins.....

    It's the very bottom gasket on the top end. And it was brand new. I hope I don't have to pull this fucker again
  13. sweatybetty89

    So it begins.....

    Yes did it as instructed will just need to do it again tmrw I imagine. They were not too loose. I'm going to go through them again
  14. sweatybetty89

    So it begins.....

    So tightened my bolts to 30 lbs. The bike needs to be cold to do this? If so I did it wrong second it's still leaking oil. And once I set cam chain tensioner I need to re set timing?
  15. sweatybetty89

    So it begins.....

    i set it flush
  16. sweatybetty89

    So it begins.....

    what is the 1mm of movement on the rod look like and i believe that i am going to be changing to a e type tensioner due to the fact that the d type sucks
  17. sweatybetty89

    So it begins.....

    well she is running and riding pretty well. i see what everybody talks about now with the vibrations. still need to properly sync the carbs. bought cheap vacuum gage on amazon and they did not work too well. is there a better product that i can use to do this? I know there is the dead cylinder...
  18. sweatybetty89

    So it begins.....

    trying my luck with the ricks unit. wish me luck ill have it wired today.
  19. sweatybetty89

    So it begins.....

    Thank you snake I've seen this and I have been looking at it for months and it finally makes sense
  20. sweatybetty89

    So it begins.....

    Here are the instructions
Back
Top