Search results

  1. littlebill31

    The $100 basket case

    Here she is boys and girls. The $100 basket case. ‘81 with 13K on the clock Looks like it sat outside on the side stand for quite a while, but its complete and after getting the engine back together, a good TCI, and a carb clean it fired right up. And now its torn down and ready to be...
  2. littlebill31

    Sold / Found / Inactive - BS34 Pilot Jets-45 & 47.5

    I need good, usable, clear BS34 pilots jets I need 2 of each...Sizes 45 & 47.5 shipped to 25443 Thanks
  3. littlebill31

    Sold / Found / Inactive - 1974 TX650

    Unfortunately I have to part with my TX650 All original, except for the mufflers. New tires New carb boots New complete Athena gasket kit (new in box) Original tool kit and manual Clean Maryland title in my name!! Runs ok, but needs valve stem seals ( I have a new set that goes with it) and...
  4. littlebill31

    Muffler for '74 TX

    After searching for quite awhile, I need recommendations for a mufflers to fit my '74 TX650. As you can see in my picture, the bracket (hanger) is bolted to the foot rest and is an ear mount. They do not fit correctly either. Sloped up as well. Yamaha shows that it mounts via bolt and it goes...
  5. littlebill31

    Finally got an all original.....

    Just picked up my all original 1974 TX650A
  6. littlebill31

    Sold / Found / Inactive - Advance Weights

    I need a pair of good advance weights. Stock, OEM, original, NOT aftermarket. Preferably in good condition.
  7. littlebill31

    Sold / Found / Inactive - Piston stop

    I need a piston stop. I tried to make another but I can't get the ceramic out completely. I wasted 4 plugs.
  8. littlebill31

    Is there supposed to be this much movement?

    Just wondering if this is correct? Seems like a lot of movement.
  9. littlebill31

    Sold / Found / Inactive - 1981 XS650

    New top end. And yes, it was done correctly. Lots of new shit. Refer to the thread below. Pamco ignition, with mew coil, plugs, wires. clean title in my name I have all receipts The issue with the ignition is fixed. http://www.xs650.com/threads/81-build-thread-the-handover.48343/ ........
  10. littlebill31

    Wanted - TCI-need to borrow one for test

    I need to borrow a known working TCI to check my bike. I will pay for postage to and from. I will also guarantee it is returned in the same working condition. Thanks
  11. littlebill31

    Sold / Found / Inactive - Advance rod

    I need an advance rod. Must be Japanese and in good condition. Not some chinese shit pot metal from Mikes
  12. littlebill31

    Timing retard/advance/Pamco

    Well, I have tried everything I can think of, but the timing is still too advanced. Fresh top end rebuild Brand new Pamco, advance rod, springs, weights, coil, wires plugs, everything, complete kit from Mikes. Advance mechanism snaps back like it should. Not sure what is going on, but at 1,200...
  13. littlebill31

    Screw for needle valve set

    Anyone know the size of the screw that holds down the needle valve set? Part # 98511-04006-00 I need 2, and Boats.net has them, but I don't want to pay $7 to ship two tiny screws.
  14. littlebill31

    Sold / Found / Inactive - BS34 Carb Top Brace

    I am in need of the brace on top of a BS34 carb
  15. littlebill31

    Sold / Found / Inactive - M-Unit, M-Button and wiring

    .....................
  16. littlebill31

    Sold / Found / Inactive - 1981

    ...............
  17. littlebill31

    Sold / Found / Inactive - '79 Special $1,000

    Selling my '79 Special. Clean title in my name. Located near Hagerstown, Md Runs New front master cylinder and rebuilt caliper. Needs front cam chain guide, new points and rear brake rebuilt. Electric starter is fine, BS38 carbs, mostly stock except for exhaust. I don't have time for it and...
  18. littlebill31

    Cylinder to Sleeve height

    I painted my cylinder and baked it in the oven. Of course the cylinder dropped a tad so the sleeve was higher than the cylinder/head sealing surface. I put it back in the oven and then used weight to get the sleeve flush again. Tapped a little to get it flush. But this got me thinking. How much...
  19. littlebill31

    Part Number help

    I ordered some OEM cam oil seals. The part number I ordered and is on the receipt is #93101-25044, but was sent #93102-25090 I ordered them from Boats.net and also double checked Partzilla, but when you search the number it pops up as part of the cam. I can't find the number of the part I...
  20. littlebill31

    Gasket Kit Price

    I bought an Athena gasket kit for $40 on Amazon, from Athena. Why does MikesXS sell the same kit for $72? Am I missing something? Same stock number
Back
Top