Search results

  1. jmink427

    Homemade and Unique Tools

    I guess I should add a link.. I made this to clean some used injectors I used on my recent EFI and Twin Turbo upgrade to my 65 Impala.
  2. jmink427

    Homemade and Unique Tools

    I made the fuel injector flushing
  3. jmink427

    Homemade and Unique Tools

    Nice!
  4. jmink427

    Well I finally started my project....

    Gonna be a dual fuel setup. The injectors in the elbow will be gasoline for driving and the four rails on the runners will be methanol for racing..
  5. jmink427

    Well I finally started my project....

    I did how work on my bike today.. Tail light bracket had broke from vibration so I had to fix it..
  6. jmink427

    Well I finally started my project....

    Some more
  7. jmink427

    Well I finally started my project....

    More pics
  8. jmink427

    Well I finally started my project....

    Been a while since i been on here.. Haven't been riding much, weather has played a big factor in that and the fact we are busting a$$ trying to get the drag week car ready. Totally changes the engine setup from a Nitrous injected 632 to a Fuel injected twin turbo 427 on Methanol... Twin 76's and...
  9. jmink427

    height limit for a brat bobber??

    I don't really know what my bike would be considered as but I'm 6' 1" @ 210lbs and mine is pretty comfortable for riding around, buy definitely not a highway cruiser... I did however move the swing arm back 3" and the fender is mounted to it so the tire doesn't bottom out against it.
  10. jmink427

    Just a little "fat".

    Yep just being sarcastic... I put two new plugs in and shut off the enrichment plunger that I somehow accidentally turn on and caused this whole fiasco and she's running good again.
  11. jmink427

    Just a little "fat".

    Think I've just about got these XS650 carburetors dialed in!
  12. jmink427

    What have you done to your XS today?

    I have a Miller Syncrowave 250 machine... I build headers all the time so its not really an issue for me burning through, but I have done it!.
  13. jmink427

    What have you done to your XS today?

    Thanks cruzin. I built the exhaust from a TC Bros exhaust kit... http://www.tcbroschoppers.com/yamaha-xs650-builder-exhaust-kit-1-5-inch-diameter.html
  14. jmink427

    What have you done to your XS today?

    What have i done to my XS today??? I "rided" it!
  15. jmink427

    BS carbs.. I get it now!

    I need to check that out.. Thanks..
  16. jmink427

    BS carbs.. I get it now!

    Got the carbs back together this afternoon and the slop in the throttle shaft is gone... :DNew seals and bushing did the trick.... I did however notice that if I cover up the vent on the diaphram on one carb it will cause the engine to go fat (rich) on that cylinder and the idle speed will slow...
  17. jmink427

    BS carbs.. I get it now!

    Not too much.. I removed the butterfly blade and shaft. Then just used a punch an hammer to tap it out towards the outside.. It came out very easy since it was a steel backed split bushing.
  18. jmink427

    BS carbs.. I get it now!

    Gary, I got my bushing turned to size and installed looks like is gonna work great... My carbs already had a bushing on the throttle shafts on the "load" side or cable side whatever you call it. So all I had to do is remove the old ones and install the new ones... I had planned to put the carbs...
  19. jmink427

    BS carbs.. I get it now!

    Got the new diaphrams from JBM Industries today.. Also got new throttle shaft seals and butterfly screws from Mikes XS, couldn't find the throttle shaft bushings at Mikes XS... I did find them on Motions website.. $.70 each... 10mm x 8mm x 8mm, but opted to make my own....
Back
Top