pamco ignition

Hi Folks, I have a Pamco ignition for a rephased motor that I ended up not using on my build. New in packaging for sale on ebay (https://www.ebay.com/itm/284235653010). I paid $105 when I originally ordered it from Pamco Pete & I have it listed for $70. Thanks!

Has anyone out there had any success replacing the hall effect sensor on a Pamco? I had a coil failure that I believe led to toasting the chip on the Pamco board but I haven't been able to find a replacement with the exact numerical code on the sensor that came in the Pamco. I sent a message...

Hey guys, I thought I would share some thoughts regarding my Pamco experience. When I began my modifications to my '81H, I jumped on the bandwagon and bought a HHB PMA...then realized I'd have to install a new ignition system as a result. I was eager and enthused and I could afford it. So, I...

I have an older model pamco ignition with E advance on my 77 chopper build. Trying to static time it but my version of the ignition has no reference marks. Missing out on all the summer riding and I desperately need advice. I need to diagnose whether or not I'm missing parts to my ignition, how...

I'm new to the forum but have been reading threads for the last couple years. Finally got the chance to do an xs build myself after a friend with a garage sold me an '81 Special motor with an accompanying hard tail frame. I was stoked. I dug right in but due to work, rookie mistakes, and other...

I've read just about every line of every thread on alternatives to the "Green Monster " Coils, but can't quite figure out if this one will work or not...

Hey guys, I recently bought a 1983 XS and was looking to install the Hugh's PMA with a Pamco Ignition System. I unfortunately made 2 rookie mistakes while doing so. My first mistake was forgetting to look at the current ignition system that was already on the bike. I assumed it was the...

Hey all, I have a 72 xs650 that has a PMA I pieced together years ago. No kits were available. I have a 5 wire reg rec combo feom Hugh if I remember correctly. Also running a pamco unit and small headlight taillight. Etc. I've tried the small cig box size batteries and killed cels in both. Now...

So I have been building a 1980 XS650 for the last 2 years. Every time I think I am close to being finished something breaks or goes wrong. I just finished rebuilding my motor and put the motor back in the frame hooked up all my electrical and tried to kick it over but I am not getting any...

What's up guys. I have a chopped, kickstart only, 81', and I'm pretty sure the ignition is kaput. About a month ago I was about to go for a ride but it wouldn't start. I kicked it for about 45 minutes until my battery finally died and no joy. Buddy came over, tried push starting, still nothing...

So I bought the basic high-output ignition setup from mikes Part #14-0911. All the hardware is installed I just need to wire everything. I have a 1975 xs650 which originally had 2 ignition coils that I replaced with 1. So now i'm left with some wires from the old coils and the old rotor/trigger...

So iv had the boyer system on my bike for about 3 years now. It was the system that came with the bike when I bought it and for the most part its been reliable except now i think it might have died. I got stuck in rush hour traffic the other night and the motor was running hot and then it the...

what is the safest way to ground spark plug while isolating a cylinder for idle mixture tuning with a pamco ignition? The new pwk carbs and manifold boots do not have vacuum ports so can not isolate that way so thinking of remove plug wire to isolate the opposite cylinder but I don't want to...

So picked up my long awaited 75 650 from a local shop after a full rebuild including Rephased goodies from Hugh, PMA, and PAMCO ignition system with all the goodies from mikesxs. The shop test road the bike for a week and called me to pick it up today. About 10 minutes away from the shop I...

Last year I built my XS650 and converted it by putting in a PMA, Pamco ignition, dual output coil, iridium plugs, capacitor, eliminted the battery. I have put over 8,000 trouble free miles on those components and they have worked as advertised. Last week I sold the bike and the new owner was...

So I just finished installing my pamco ignition. I have no spark whatsoever. I noticed that the sensor itself seems to be wired incorrectly. The three leads soldered into the board on the sensor are red green and black. The board is also labeled this way. BUT the red and green are reversed. Can...

I am looking to redo my ignition on my 78 xs650 special. Need some recommendations on the best kit for the money from mikesxs. Was looking at this kit: https://www.mikesxs.net/product/14-0913.html Will that give me everything to throw out my points and mechanical advancer? It has the auto...

Hey guys, So I bought a brand new pamcopete ignition and hughshandbuilt pma recently and just attempted to install the pamco today. I took the advance rod out and have the entire left side complete (sensor plate in place etc.). Now, I have a 1979 special...do i need to replace the right...

Bought a Pamco original unit in 2008 .. the 1st unit he came up with. At the time Mikes #17-6803 coil was recommended and this combo has served me well for 5 years. I am electrically challenged. Bike quit yesterday, it has always worked great. Here is what happened: Went for a ride as usual ...

Hey guys, new to the forums here. My stator crapped out on me so I decided to upgrade to PMA. My bike is a 83 special so I need points or pamco. I ordered the kit from mikes to have them tell me 4 days later they are refunding me my money because they don't have e advancer or high output coil...