Search results

I have a few 1978 XS 650 Special Parts left Sidecovers $25 + shipping (sold) Tank with petcocks $50 + shipping (sold) Stock Handlebars $10 + shipping (sold) Starter $25 + shipping Exhaust (Stock) $100 + shipping crash bar $10 + shipping guages...

make me an offer on this exhaust, nice shape no rot, not perfect but nice their off a 1978 xs 650 special

For sale XS 650 Parts, Heres what i have left Head complete $100 + shipping USA Jug $50 + shipping USA Side Covers Pair $40 + shipping USA Wheels Pair $100 + shipping USA...

make me an reasonable offer on my calipers

complete wire harness off a 78 xs 650 and any electronic parts, i have complete bike parting out,Thank you ask me what you need

for sale is a nice pair of stock exhuast comlpete,nice chrome stock pipes,pictures by email only,Thanks They are off a XS 650 Special

Parting out a 1979 650 motor let me know what parts you want and make an reasonable offer Pistons (stock) $25 apiece + shipping Head $150 + shipping Jug $75 + shipping Clutch cover $25 + shipping Stator cover $25 + shipping stock coil $25...

Opps ! mis print

Hello, I'm partinting out my XS 650. I have the title for the frame for $300-USA carbs $150 for the pair-USA mag wheels with decent rubber $200 for the pair only-USA pamco ignition $150-USA seat with new cover $100_USA two starters $50 each-USA engine needs conneting rods replaced $300...

Hello people, would someone tell me if there is a way to check the hole where the rist pin goes through the connecting rod, can i mic them, or do they need to be replaced once they show alittle bare metal?:yikes: thank you

Hello xs650ers, would someone tell me how to set the piston ring gaps, i understand the rings are to be turned away from each gap, im sure there must be a certain way my book isnt real clear on where to put the gaps, Thank u:shrug:

Hello, would someone tell me the best way to install the masterlink in the cam chain? Thank you

For Sale 1978 xs 650 $800 low end noise:doh:

for some reason my engine is making a really loud noise, it just started, i have no miles on the motor, the noise gets louder the more gas you give it , the noise sounds like the something is rubbing on something in the motor, i just put new rings,had the cylinders honed,head done,front cam...

Hello xs650 members, I noticed alot are asking for recommendations on oil for their rides, well, I invite you to check out my website: bntsynthetics.com Amsoil provides a product especially formulated for every application. I have used and sold this product for several years. Let me show you...

Hey, could someone tell me why i still have a leak after replacing the clutch push rod seal? i have checked the rod to match sure it wasnt bent, i made sure that the rod was clean and i cleaned the area of any grime.THANK YOU for any input:shrug:

I just rebuilt the top half with new rings,jugs honed,etc. and my compression only about 120 psi, and im reading others saying there compression is around 150, is my psi low cuz the rings havent seated yet, or something else?:yikes:

Hello, i just recently rebuilt top half of motor, i have it put back together, how do i adjust the cam chain and how do i tell that it is adjusted enough or to much? I rebuilt motor do to it had a blown head gasket or atleast thats how i bought the bike.

Hello, i was wondering if someone could tell me if the is any sealent needed for the bolts on the front side cam chian guide bolts that are located behind the oil tube, i just rebuilt the top half of the motor,replaced the copper washers and it seems to be leaking oil from them:yikes:

i was wondering if someone could tell me why the rightside pipe is hotter than the leftside,i just recently rebuilt the top half,new rings,gaskets,etc. i have taken the carbs off and cleaned, i noticed the mixture screws have a plastic cap on them,and when it does start it hits on the leftside...