And if I look hard enough I am betting that I have the email stating from Mikes to have the bike timed at the 15 degree mark at idle.
November 7, 2019 Motorcycle Electrical,
Motorcycle Generator Brushes,
Motorcycle Ignition,
Motorcycle Pistons,
Motorcycle Tools,
Motorcycle XSCharge,
Tech Center
How To: Install The XSCharge XS650 PMA Kit
XSCharge XS650 Permanent Magnet Alternator Installation Instructions
1. Remove the shifter, footpeg and side cover.
2. Remove the chain guard that is mounted to the shift shaft and remove the wire from behind it.
3. Remove the original charging system. Begin by first removing the two Phillips head factory screws from the stator assembly. This works best when using an impact driver. You will not be reusing them so do what is necessary to remove them as they can be hard to remove. Remove the stator assembly.
4. Remove the rotor assembly. First, remove the retaining nut and lock washer. The easiest way to remove the rotor from the crankshaft is with a factory threaded puller which can be purchased
here. Be very careful with these type pullers to not damage the threads on the end of the crankshaft. The crankshaft is tapered and you should be able to put some pressure on the puller and using a hammer tap the lead screw on the puller and remove the rotor.
5. Remove the small locating pin at the bottom of the crankcase.
6. Take the new adapter bracket and stator assembly and check it for fit. It should fit fairly snug inside the alignment tabs on the engine case. The clearance on these alignment tabs and the height of the mounting bosses can vary some from the factory so do not force the adapter bracket into place. You can mark it and use a file if necessary to get it to seat against the engine
block and mounting screw bosses.
CAUTION: Make sure that the plate fits completely against the threaded mounting bosses where the mounting screws go. Check both sides and if there is a gap behind the adapter on either side between the adapter and the mounting boss, use the extra small washers, supplied in the kit as a spacer. Only use them if a spacer is needed.
When the fit is correct, install the woodruff key back in the crankshaft if you have removed it. Using the two socket head screws, flat washers, and lock washers that are supplied in the kit, now it’s time to mount the adapter. These screws should be applied using Blue Loctite.
Do not overtighten these screws as you can strip out the engine case.
(The first picture is only to show the screw location, your bracket will have the stator already mounted)
7. Carefully line up the key slot in the rotor with the woodruff key already located in the crankshaft and slide the rotor on, being careful to not dislodge the key. Install the crankshaft nut and lock washer snuggly but
DO NOT tighten completely. Rotate the engine slowly, making sure that there is no rubbing or scraping of the stator and rotor. If this occurs, you will need to remove the rotor, loosen the adapter bracket mounting screws and realign the bracket and retighten the screws. When this is complete, check again, making sure of proper alignment and then,
torque the crankshaft nut to 29 ft-lbs.
8. Route the wires through the cutout in the engine block and press the rubber grommet into place. You may need to carefully trim the black outer wire cover to get a correct fit. You can now route your new wires behind the chain guard on the shift shaft and reinstall. This is what the assembled unit should look like.
9. Reinstall the side cover with the inspection cover off. Now, you will need to mark
TOP DEAD CENTER (TDC) for timing purposes since the original timing marks were on the discarded factory stator. You can mark the
TDC mark on the lower flange of the side case behind where the inspection cover goes. There is a notch in the case below the flange. Make your
TDC mark line up with the
right side of the notch.
Remove the spark plugs. Slowly rotate the engine so that the piston reaches its highest point of the stroke. You can see this through the plug hole using a light or you can locate this by placing a soft object like a drinking straw into the plug hole and watch it reach its highest point on the stroke.
When you have located
TDC, hold the crankshaft perfectly still and you will need to mark a line on the rotor in line with the
TDC mark you previously placed on the flange. Mark it accurately with a marker and then you can scribe the line with an etching tool. Make another line on the flange at
.500 inches to the left of the
TDC mark that you made and that gives you the
15-degree mark.