Yes please.... share with us. Looks great!My plating has gotten MUCH better. I've completely re-done my plating set-up, and figured a lot of stuff out. I need to write an update for Jim's plating thread.
Yes please.... share with us. Looks great!My plating has gotten MUCH better. I've completely re-done my plating set-up, and figured a lot of stuff out. I need to write an update for Jim's plating thread.
Very pretty!View attachment 166567
I restored the XS1B's brake lever using (almost) all of the original parts. Still waiting for that critical part to come, and then I'll reveal what the rest of the bike currently looks like.
View attachment 166568
These steel parts give an idea of the condition the lever was in. One of the few parts that I didn't re-use was that threaded brass sleeve (red arrow). You can see how worn it is. That wear equals lever slop. As far as I know, that threaded sleeve is unobtainable, but I found a steel one in my Big Box O' Brake Junk.
View attachment 166569
Here are the steel parts after nickel plating. My plating has gotten MUCH better. I've completely re-done my plating set-up, and figured a lot of stuff out. I need to write an update for Jim's plating thread. Most of this stuff can be bought NOS on eBay, but what's the fun in that, and besides, the whole reason I started plating was so that I wouldn't be nickel-and-dimed and have to wait for shipping on little bits like this.
View attachment 166574
My one regret is that I didn't sand the head of this bolt (the long pivot bolt) smooth before I plated it.
View attachment 166575
For the handlebar pinch bolt I used a stainless steel bolt. I grinded the grade markings off of the head, and then wheel-polished it. This is extremely satisfying. It takes just a few short minutes to transform an ugly bolt into a perfect little gem.
BTW, I have to apologize to 5twins on this subject. A few years ago he was showing off some stainless bolt heads that he had done the same thing to, and I made fun of him, saying that "if you're polishing bolts, you have too much time on your hands." I take that back, and thanks for a great idea. I polish all of my stainless bolt heads now in situations where they show on bikes that matter.
View attachment 166653
That washer on the bottom of the brake light switch is the only other thing that I replaced. Replaced the rusty original with this big fender washer -- it's on the bottom, where no one will see it.
Just used regular black heat shrink tubing to replace the switch sheath. Could have bought reproduction silver sheath, but that would have meant spending money, and re-doing the two bullet connectors, and besides, it looks like the cabling on this bike will be a mix of black and silver anyway.
Oddjob, did you ever get your carb boots from Heiden?DogBunny, I bought the set from Heiden tuning €40 (45USD), the only other option that I could find was JBM industries @ 74USD.
Despite the fact that I put in my order prior to the complete travel lock-down, it appears that my parts have been stuck with Post-Netherlands since Mar 30, probably waiting for a flight over here. Not Heiden's fault, just another sign of the crazy times...
Good attitude.I'm not blaming anyone... Compassion, kindness, gratitude, etc. they all apply, not much I can do beyond that...
Yes, thank you very much. I really appreciate it. Maybe I have something you can use.I think that I might have a nice replica emblem to fit on the RH sidecover.
Hi DogBunny,
I placed my order in the third week of March and they shipped with a tracking number at the end of March...
Since then... it sat at PostNL for about a month, and it looks like it was probably placed in a container and shipped by sea (by PostNL) at the beginning of May... This is just a guess, but at least that's what I hope happened. Typical transit times would 2-3 weeks for a container so well see...
Covid has hit the Netherlands quite hard (as it has the entire world) so I'm not blaming anyone... Compassion, kindness, gratitude, etc. they all apply, not much I can do beyond that...
View attachment 167002
Yes, thank you very much. I really appreciate it. Maybe I have something you can use.
Sending you a PM...
Getting a bad spoke occasionally just happens. I've encountered it with several different sets for different bikes, from different makers, and in both stainless and cad plated. That's why I now immediately fit the nipples to every spoke when I get the set, just in case.
Thanks for selling me 7 of these. They look great.View attachment 165674
For the rubber front wheel plugs, I got a chance to try an idea that I've had for a long time. I used 1-3/8" locking black nylon hole plugs from McMaster-Carr. The holes in the hub are actually oval, and the nylon hole plugs are pretty rigid, so I had to cut relief slots into the walls of the nylon plugs as shown. Using a Dremel cut-off wheel, I cut four slots in each plug, spaced 90 degrees apart. The hub will accept the nylon plugs without the slots, but it distorts the plug. Even with the slots, it's not absolutely perfect, but it's pretty close, and looks very sharp.
I suppose that alternatively, you could make the oval holes in the hub round, but then you'd be irreversibly altering the stock hub.
I had to buy a package of 50 of those nylon plugs, so if anyone else wants to try this, I've got the plugs.
IAnd so it begins.
This is the 1971 XS1B that was posted for sale two weeks ago.
Condition is not really good enough for this to warrant the time and money for a true restoration -- instead it will be a resurrection, but I do intend to make it nice.
I have about $400 including gas in it -- was 400 miles and an 8 hour round trip away.
My immediate need is for a seat. I can go a couple of ways with this -- I have a nice, complete, 1973 tin set that I could use, or I can use the existing tank and side covers. So, I can use any seat from 1970 to 1973, in any condition if anyone has one.
B T W the bike came with a rack that is probably pretty rare. It has some rust, but is otherwise pretty nice, if anyone is interested in it.
View attachment 158603
View attachment 158604
I think it would be a great candidate for a full resto ! especially at that starting price ! And a lot of fun doing it !And so it begins.
This is the 1971 XS1B that was posted for sale two weeks ago.
Condition is not really good enough for this to warrant the time and money for a true restoration -- instead it will be a resurrection, but I do intend to make it nice.
I have about $400 including gas in it -- was 400 miles and an 8 hour round trip away.
My immediate need is for a seat. I can go a couple of ways with this -- I have a nice, complete, 1973 tin set that I could use, or I can use the existing tank and side covers. So, I can use any seat from 1970 to 1973, in any condition if anyone has one.
B T W the bike came with a rack that is probably pretty rare. It has some rust, but is otherwise pretty nice, if anyone is interested in it.
View attachment 158603
View attachment 158604
Thanks, but, I already have a blue 1973 -- the Super RustBucket.Looking good!
Diggin that blue.
Thanks, but this will be a resto-mod, not a resto. I've already changed the forks from 34 to 35mm.I think it would be a great candidate for a full resto ! especially at that starting price ! And a lot of fun doing it !
Are you still in need of a seat? Mine won't be available immediately but eventually. (within a month, I hope)My immediate need is for a seat. ... So, I can use any seat from 1970 to 1973, in any condition if anyone has one.