Media added by YAM277

Navigation

  1. XS650 Originals and Restorations 175
  2. XS650 Choppers 31
  3. XS650 Bobbers 126
  4. XS650 Trackers 163
  5. XS650 Cafe Racers 102
  6. XS650 Slightly Modified 139
Browse albums

Media comments

  • P
    Spoiler
    where can I get this spoiler
  • Tony Harrell
    CLASS ACT 06
    Couldn't remember your name after first seeing your work , but finally found you and got it bookmarked ! Love all your builds!

Most media items

  1. YAM277
    510

    YAM277

  2. TwoManyXS1Bs
    502

    TwoManyXS1Bs

  3. I am Carbon
    500

    I am Carbon

  4. Mike G
    466

    Mike G

  5. Mailman
    463

    Mailman

Media statistics

Categories
6
Albums
2,942
Uploaded media
25,464
Embedded media
18
Comments
1,626
Disk usage
4.6 GB
IMG 47- Axle bearing shown without 1mm washer installed. . . yet.

IMG 47- Axle bearing shown without 1mm washer installed. . . yet.

  • 0
  • 0
IMG 46- 1mm washer top left, spacer top center and 2mm washer top right. Followed by 1mm washer before thrust bearing bottom left, thrust bearing bott

IMG 46- 1mm washer top left, spacer top center and 2mm washer top right. Followed by 1mm washer before thrust bearing bottom left, thrust bearing bott

  • 0
  • 0
IMG 45 Finished version of the back of the Primary Drive Gear Gear, showing the new cush springs.

IMG 45 Finished version of the back of the Primary Drive Gear Gear, showing the new cush springs.

  • 0
  • 0
IMG_2541

IMG_2541

  • 0
  • 0
IMG 44- Additional pic of finished cush spring install.

IMG 44- Additional pic of finished cush spring install.

  • 0
  • 0
IMG_2542

IMG_2542

  • 0
  • 0
IMG 43- Shot Peening applied, if you are worried about the nut falling off.

IMG 43- Shot Peening applied, if you are worried about the nut falling off.

  • 0
  • 0
IMG_2543

IMG_2543

  • 0
  • 0
IMG 42- Careful not to peen downward to hard on Aluminum Clutch Housing. Strike towards the sides or edges.

IMG 42- Careful not to peen downward to hard on Aluminum Clutch Housing. Strike towards the sides or edges.

  • 0
  • 0
IMG_2544

IMG_2544

  • 0
  • 0
IMG 41- 5mm Hex Bit socket inside clutch housing and 13mm socket on the back of the primary drive gear. Torque specs were just hand tighten snug, with

IMG 41- 5mm Hex Bit socket inside clutch housing and 13mm socket on the back of the primary drive gear. Torque specs were just hand tighten snug, with

  • 0
  • 0
IMG_2545

IMG_2545

  • 0
  • 0
IMG 40- 13mm socket used on the backside.

IMG 40- 13mm socket used on the backside.

  • 0
  • 0
IMG_2546

IMG_2546

  • 0
  • 0
IMG 39- Let gravity take it's course around the threads, lightly applied.

IMG 39- Let gravity take it's course around the threads, lightly applied.

  • 0
  • 0
IMG_2547

IMG_2547

  • 0
  • 0
IMG 38- Red Permatex or Red Loc-Tite

IMG 38- Red Permatex or Red Loc-Tite

  • 0
  • 0
IMG_2548

IMG_2548

  • 0
  • 0
IMG 37- Try to angle the cut on the adhesive tip, for better control, when applying the product.

IMG 37- Try to angle the cut on the adhesive tip, for better control, when applying the product.

  • 0
  • 0
IMG_2549

IMG_2549

  • 0
  • 0
IMG 36- Steel plate laying on the primary drive gear, with spacers showing below the hole.

IMG 36- Steel plate laying on the primary drive gear, with spacers showing below the hole.

  • 0
  • 0
IMG_2550

IMG_2550

  • 0
  • 0
IMG 35- Better shot showing the spacers, before the steel plate is fastened.

IMG 35- Better shot showing the spacers, before the steel plate is fastened.

  • 0
  • 0
IMG_2551

IMG_2551

  • 0
  • 0
Back
Top