front end coming together.

front end coming together.

  • 0
  • 0
HipShot Eng. made nearly 20 sets of these on a very old HERBERT auto Turret Lathe. awesome

HipShot Eng. made nearly 20 sets of these on a very old HERBERT auto Turret Lathe. awesome

  • 0
  • 0
no brainer

no brainer

  • 0
  • 0
Clutch spring spacer bolts from HipShot Eng.

Clutch spring spacer bolts from HipShot Eng.

  • 0
  • 0
mmmmuch more good

mmmmuch more good

  • 0
  • 0
that little heart shaped thing fits my valve adjusters. It's just mad how it came along when i got to the point where i needed a thing to do that job.

that little heart shaped thing fits my valve adjusters. It's just mad how it came along when i got to the point where i needed a thing to do that job.

  • 0
  • 0
shall i trim that gasket??? or, maybe i'll show off a bit first. it's very bright :o)

shall i trim that gasket??? or, maybe i'll show off a bit first. it's very bright :o)

  • 0
  • 0
I'm so proud

I'm so proud

  • 0
  • 0
pistons are IN all went well, they turn smoothly and feels good to me. my stator cover was so mashed i had a brass one turned up. i like it but it

pistons are IN all went well, they turn smoothly and feels good to me. my stator cover was so mashed i had a brass one turned up. i like it but it

  • 0
  • 0
2014 08 29 22.08.38

2014 08 29 22.08.38

  • 0
  • 0
2014 08 29 20.52.45

2014 08 29 20.52.45

  • 0
  • 0
wish i'd blasted the crank cases. They are spotless but bit tatty lookin

wish i'd blasted the crank cases. They are spotless but bit tatty lookin

  • 0
  • 0
Hamlyns Eng. in bridgewater, somerset did a great rebore and hone for about 80 quid

Hamlyns Eng. in bridgewater, somerset did a great rebore and hone for about 80 quid

  • 0
  • 0
those socket bolts holding the camchain guide are too big, they interfere with the oil feed pipe

those socket bolts holding the camchain guide are too big, they interfere with the oil feed pipe

  • 0
  • 0
lowering the barrels. once pistons are in, i pushed out the pins and dropped the barrels down, con-nected up to the..what are they called....? and put

lowering the barrels. once pistons are in, i pushed out the pins and dropped the barrels down, con-nected up to the..what are they called....? and put

  • 0
  • 0
that bit of wood and its longer brother were so useful. Thanks to this forum for the engine-you-ity

that bit of wood and its longer brother were so useful. Thanks to this forum for the engine-you-ity

  • 0
  • 0
you KNOW what that bit of string is for... i'm lovin the agled grindered edges on the fins

you KNOW what that bit of string is for... i'm lovin the agled grindered edges on the fins

  • 0
  • 0
oily base gasket. hasn't hurt. i'm still in the running-in period right now where i'm still torquing up after each little run. Now the whole gaske

oily base gasket. hasn't hurt. i'm still in the running-in period right now where i'm still torquing up after each little run. Now the whole gaske

  • 0
  • 0
my rustic mechanics tool

my rustic mechanics tool

  • 0
  • 0
lift that cam chain up!

lift that cam chain up!

  • 0
  • 0
everythings ready. 533 pistons with inner circlips and wrist pins installed - CHECK rings gapped and fitted - CHECK cam chain held up with wire w

everythings ready. 533 pistons with inner circlips and wrist pins installed - CHECK rings gapped and fitted - CHECK cam chain held up with wire w

  • 0
  • 0
took a dremmel to the flashings inside the ports. didn't go mad, then blasted them with fine glass media. looked awesome and smooth. New stainless ex

took a dremmel to the flashings inside the ports. didn't go mad, then blasted them with fine glass media. looked awesome and smooth. New stainless ex

  • 0
  • 0
the .25 over pistons, no good to me.....

the .25 over pistons, no good to me.....

  • 0
  • 0
well, i blasted and painted the barrels with Calfire Stove Paint, we'll see how it goes. then ran the angle grinder with a flap-wheel over the fins t

well, i blasted and painted the barrels with Calfire Stove Paint, we'll see how it goes. then ran the angle grinder with a flap-wheel over the fins t

  • 0
  • 0
snailstoves

The Build Down and Tear Up - Backward Album

about bloody time too
Click to expand...
There are no comments to display.

Album information

Album owner
snailstoves
Date created
Item count
74
View count
6,088
Comment count
0
Rating
0.00 star(s) 0 ratings

Album privacy

snailstoves

snailstoves

Media items
80
Albums
2
Can view media items
Everyone
Can add media items
Album owner only

Share this album

Back
Top