Media added by YAM277

Navigation

  1. XS650 Originals and Restorations 178
  2. XS650 Choppers 31
  3. XS650 Bobbers 126
  4. XS650 Trackers 163
  5. XS650 Cafe Racers 102
  6. XS650 Slightly Modified 147
Browse albums

Media comments

  • gggGary
    Jim's Paint
    Love Jim's painting!
  • Tim Meaders
    Spoiler
    This was my original one-off design, it was scrapped and replaced with a new wider version.
  • P
    Spoiler
    where can I get this spoiler

Most media items

  1. YAM277
    510

    YAM277

  2. TwoManyXS1Bs
    502

    TwoManyXS1Bs

  3. I am Carbon
    500

    I am Carbon

  4. Mike G
    472

    Mike G

  5. Mailman
    463

    Mailman

Media statistics

Categories
6
Albums
2,942
Uploaded media
25,481
Embedded media
18
Comments
1,628
Disk usage
4.6 GB
The convincer! located in bottom left of pic!

The convincer! located in bottom left of pic!

  • 0
  • 0
IMG 0735

IMG 0735

  • 0
  • 0
IMG 0799- new 8 hole gasket.

IMG 0799- new 8 hole gasket.

  • 0
  • 0
IMG 11- Secondary 23/64 bit did not have to go in very far, maybe a 1/4 of an inch, before it grapped and I was able to work it out easily. If this bi

IMG 11- Secondary 23/64 bit did not have to go in very far, maybe a 1/4 of an inch, before it grapped and I was able to work it out easily. If this bi

  • 0
  • 0
Acorn nut with copper washer and blue locktite

Acorn nut with copper washer and blue locktite

  • 0
  • 0
IMG 0800- note washer that goes on brass neck.

IMG 0800- note washer that goes on brass neck.

  • 0
  • 0
Acorn nuts (6), this is using the first chart, as a preference, not the second chart.

Acorn nuts (6), this is using the first chart, as a preference, not the second chart.

  • 0
  • 0
IMG 0737

IMG 0737

  • 0
  • 0
IMG 0776

IMG 0776

  • 0
  • 0
IMG 0775- Looking down from the top, it was easy to apply pressure to the top of the brass fitting, with the butt end of the screwdriver, with slow a

IMG 0775- Looking down from the top, it was easy to apply pressure to the top of the brass fitting, with the butt end of the screwdriver, with slow a

  • 0
  • 0
IMG 12- The Doctor has made a clean extraction!

IMG 12- The Doctor has made a clean extraction!

  • 0
  • 0
Who says a toaster oven won't work?

Who says a toaster oven won't work?

  • 0
  • 0
5th gear overdrive, supplied by Mike's Xs. BE FORWARNED!!! You will have to have a machine shop open the inside diameter of the gear, to match the ori

5th gear overdrive, supplied by Mike's Xs. BE FORWARNED!!! You will have to have a machine shop open the inside diameter of the gear, to match the ori

  • 0
  • 0
IMG 0798- cover placed on it's back, towards left side of pic.

IMG 0798- cover placed on it's back, towards left side of pic.

  • 0
  • 0
IMG 19- Locking washer shown with sealant up against sprocket.

IMG 19- Locking washer shown with sealant up against sprocket.

  • 0
  • 0
Been waitin' a long time to do this!

Been waitin' a long time to do this!

  • 0
  • 0
IMG_1395

IMG_1395

  • 0
  • 0
IMG 14- 36mm socket used for best results.

IMG 14- 36mm socket used for best results.

  • 0
  • 0
IMG 0797

IMG 0797

  • 0
  • 0
Opposite side of bottom case, with M8 nut, washer and blue locktite. This is #9 on locator picture chart.

Opposite side of bottom case, with M8 nut, washer and blue locktite. This is #9 on locator picture chart.

  • 0
  • 0
IMG_1401

IMG_1401

  • 0
  • 0
IMG 23- 5Twins has helped us out again, by telling us a tip on how to further prevent leaks, hope this picture does his explanation some justice. Don'

IMG 23- 5Twins has helped us out again, by telling us a tip on how to further prevent leaks, hope this picture does his explanation some justice. Don'

  • 0
  • 0
Last pic, before closing 'em up!

Last pic, before closing 'em up!

  • 0
  • 0
IMG 12- Locking washer bent over to assure extra measure of safety.

IMG 12- Locking washer bent over to assure extra measure of safety.

  • 0
  • 0
Back
Top