Search results

Back in the days when I was building Yam's in my garage I joined this forum. It has been a long time since I have done this but I am starting back up again. This is one that I built back then. The first pic is the bike as I received it. I then did all the work to make it a cafe, including the...

Sold separatelyl This just came off my 74 XS650 with only 4k miles on it. Rear fender....Tail light assembly. I also have rear and front blinkers. Fender...$90 Tail light assembly....$90 Rear blinkers.....$75 Front blinkers .... $65 Shipping is extra depending on where and how.

seat for 1974 XS650. No tears. good condition. See it in pix on bike now. $90 plus shipping. Speedometer and Tach with key. $100 plus shipping

I have a clean stator for electronic ignition xs650. $25 shipped.

I spent some time looking but did not find a solution to my problem. I am trying to wire in an old style regulator with three wires. Can someone enlighten me as to which goes where?

For sale is my 72 Anomoly. Frame and motor have 72 serial numbers though the frame appears to be that of a 74 as it had the tubular rear footpeg mount. Engine and frame are matched serial numbers. rear grab rail cut off, rear footpegs cut off, centerstand cut off, and I still have those parts to...

Since I changed to 2 exhaust right, I had to remove the center stand. My frame is a 74 type. I also have the rear grab rail and two rear footrest tubes that I removed. Take it all or part. The more you take the cheaper it gets... Center stand $40 shipped, includes bolts and spring Grab rail...

Here is a stock set of pipes, wrapped, and a unused set of mufflers from a Harley Sportster around 2010 model. I had them on the café in the pix but have since changed the whole bike to a bob/tracker and acquired 2 to 2 both right side system. These ones I am selling were on the bike but it...

What are the sizes on ex and int valves? (face width)

bought a set ogf good 2 to 2 exhaust pipes that are terminal on right side. They bolt right up to existing frame location. I could not use them because I didn't want to pull my center stand. If no mufflers were attached they would fit but I want mufflers. $100 plus shipping.

The tag on the underside of this seat is 447-10. what is pictured is as it is. Pretty good metal and trim, hardware. Small tear in fabric. boots are new and for 72 XS650. Seat $75 shipped USA Boots. $25 shipped USA

I recently installed stock airboxes on my TX650. In between the boxes is a rubber boot. My question is "How critical is it that the boot be secured air tight to the metal"? I fabricated one from inner tube rubber and firmly secured it to one side. I cannot get my paws in there to secure the...

I am looking for part # 8,9, 10 (2ea) and 1 of 13, 14.

I have installed a set of metal airboxes on a 74 frame. I need the boot that connects the two boxes and carb to box boots.

Gary sold me these air boxes for my 72/74. Perfect fit!

I am changing jets on BS38 carbs. I see on the jet that there is 2 small grooves. Are there supposed to be Orings?

I have a 74 frame and bought these plastic ones. They do not fit. I will get pix later. I need the metal ones. Make me a decent offer.

I have this 78 xs650 tank for sale. Some rust inside. Comes with petcocks and original side badges. $80 shipped in USA.

I am thinking of using some new VM slide carburetion for my xs650. Has anyone got any experience with this? What size jetting, venturi, etc...

I am just about done with this 83 xj550 Seca. It is pretty much all original. I still have to install the pods, tune the carbs, and bleed the brake...Then I need to figure out how to install the fairing..