Search results

Titled 1971 XS1B frame with numbers matching engine (crusty and has a broken cooling fin), additional 71 engine (pictured), pair of shouldered wheels, 1970 xs1 forks, boxes and boxes of parts mostly 70-72. Frame is a rolling chassis that has the TX750 swingarm and rear wheel swap and...

Pictures tomorrow. Frame is stock and uncut. No missing tabs etc. None running engine with 1 broken fin. Have the fin. Send me a private message. Looking to move it ASAP.

Looking to buy a functional complete right front turn signal from a 1971 XS1B. Thanks in advance.

Nice late 70's rear fender/tail light, rear disc brake swing arm with caliper etc, 72 front caliper, 72 right handlebar switch and throttle assembly, another tail light like the one on the fender, rear signals, two more swing arms, and shocks. $99 for the pile in Indianapolis, IN.

Looking to repair or replace my current switch. Need turn signal guts or a complete functional unit. Cash or trade for other early parts.

Had the top end freshened up on my 71 XS1B by Dan Watson of Watson Racing Services because it had 33,000 miles on it. Runs and sounds better than any other XS I have owned. Carbs are beautiful and have the proper Mikuni jets for a 71. Put 100 miles on it to break it in as suggested here on the...

Found One.

Non Charging issue on XS1B. Specifics inside. I have a 2 Volt drop from battery to the brown wire coming out of key switch with the key on. I have full battery voltage all the way to the red wire entering the key switch. Charging guide points to a bad key switch. Are they serviceable...

Looking for a pair in good useable condition.

Looking for a clean useable left hand bar switch. Looking for something with the gray outer wiring covers intact.

Looking for a stator side engine cover for my XS1B project. Prefer something that has not been puked all over by the carbs and battery. Willing to settle for something less than perfect just to get it back on the road until the right one comes along. Please refer to this thread for help...

Found one.

Looking for an unmolested wiring harness in good useable condition for a 1971 XS1B. Cash or trade.

New never used. I will upload a picture when I get to the shop in the morning. Here is a link to their ebay listing for reference until then. $45 plus the ride. http://www.ebay.com/itm/191028848114?_trksid=p2059210.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT

1972 Yamaha XS2. Frame and engine numbers match. Clear title in my name. Starts with one kick, electric start is not currently working. Starts, runs, and shifts through all gears. Paint is faded. Chrome does have some pitting and surface rust on areas. Handlebars, exhaust, and rear fender...

Both appear dent free to me. One tank has been rattle canned flat black. Some light rust inside. Would clean up nicely. No petcocks. Cap has key. Tank was originally blue. $79 plus the ride. Other tank was taped off around the original decals and painted off white/cream. Interior...

Can someone point me in the direction of ways to distinguish between 70-73 carb bodies and the 74-75 bodies? Same thing with the bowls. Is there any interchangeability between the bodies and bowls on these years with the difference in the needle jet? Bowls are marked with an A on the bottom...

Can someone point me in the direction of some images to help me tell the difference between carb bodies and bowls 70-73 vs 74-75? Thanks in advance.

I have a stock 1972 XS2. Run an AGM battery. Installed a PAMCO w/ E Advance last summer. Ultimate coil. Bike has started first kick ever since. Yesterday I kicked it over and it started right up, but I quicklyly realized it was only running on one cylinder. I shut it down immediately. I looked...

Looking for a pair of each. Parts 12 & 15 in the diagram. White plastic piece in the photograph is an upper. Let me know if you have any of either one. Thanks in advance.