Search results

Located in SW. Louisiana. Typical xs chop. Lots of goodies, just needs the carbs rejet and slap the chain on. Just need the money for school. Texas title, not in my name. Hughs pma, high output pamco, 2 Sparx caps w/o battery, vm roundslides, tc bros hardtail, biltwell hinge, custom mids...

Test fit them on my bike. Didn't like the green against the green on my tank.

Do I necessarily "need" both? I'm running a tc hardtail and monstercrafstman chain tensioner and I absolutely hate the look stock axle adjusters. I was under the impression that the axle adjusters were used mainly to account for slack in the chain.

I've read all the Links on how to convert my 9 digit vin code to the 17 digit code but to be honest my ADHD is so bad I get lost after about two paragraphs. Can some one please help me convert this vin 3G0-005459 to the 17 digit code.

Looking for the dust cover/spacer that goes on the chain side of the rear axle.

Hey guys, just finished up my build this morning an I'm having problems getting it running. It will start when ether is sprayed into the carbs but its like its at WOT. Getting spark, and getting gas to both carbs (checked the bowls at drain). Running hughs pma, 2 caps in a series, pamco and VM's...

Perfect for you if you're upgrading your brakes to Harley or street bike calipers! This is a brand new, never used NISSIN 5/8" MC with 6 position lever for 7/8" bars. It is equipped with a 14mm reservoir but its PERFECT for the mini tube reservoir mod! I needed a 1/2" piston and accidentally...

Brand new Magura 314 throttle and 1-2 cable for vm34s, just looking for a different throttle. Also willing to take trades. Looking for a different throttle, rear tire, electronics box, grips, solo hinge, etc. Just let me know what you have and we can work something out.

I'm nearing the end of my build and I have a few head scratchers. I bought a Cole Foster tank off of a member (either here or CC) and it came with a ball bearing petcock and two nipples installed on the front bottom of the tank. What do these nipples connect to, and do I just run a single fuel...

Can I make this Master cylinder/brake lever fit on my 1980 xs with the stock caliper? It has a remote reservoir so I can replace it with the right size.

My bs38s are all gummed up and As I was already interested in upgrading to flatslides, what better time than the present? Let me know what you have. We can work out a trade with my stockers + cash if you're interested...

im cleaning my bs38s off my 1980 and I cannot seem to get the copper tube that the main jet screws into out. I watched a tutorial and he used a sliver of wood but mine seems to be stuck in there pretty good. I know not to use steel as the copper is weaker. Any help or insight would be...

2.9g Sporty Tank PRICE DROP! Fresh flat black paint (actual HOT ROD FLATZ black urethane, not rattle can). Chrome cap. A little rust inside, easily cleaned with electrolysis/mekp. Just going with a different tank on my build. $90 shipped obo...

:confused:So my hugh's handbuilt PMA just came in, and next week i'm ordering my pamco kit. My bike is currently in pieces thanks to the previous owner, and as I was searching the forum for the PMA installation thread, I read that it would be better to do the pamco first....Should I wait to...

I wanted my own mic taillight, but could not justify spending $300+ on a Seven Sins light. Soooo after stumbling onto a how to on chopcult, I decided to make my own. I used a Shure 55 series mic, gutted it, and used aluminum tape that I got from work (i'm an industrial fiberglass tech) and...

I'm about to order my PAMCO from Mikesxs.com, but my question is, which should I buy? I have a 1980 650 so I know I need a certain one. I am looking at the high output units for the simplicity of replacing the wires. I'm just wondering if I need the ones with the "+advance" or not....

Im not sure the year of this tank but ive noticed it has 2 openings at the bottom, one for the petcock (mid left) and some other little nipple on the right that has a rubber cap on it. What is that nipple for, and what petcock do I need to ensure clearance for the cylinder head? All I know is...

This was on my bobber project when i got it. It's not exactly what I'm looking for seeing as I've got a tc bros air ride setup. Willing to trade or sell. Its a corbin, im not really sure what kind of bike it was made for. I can take a pic of it on the frame if you're interested in how it fits as...

I'm rebuilding my front end and I'm having a hard time finding the right size bearings for a 1980 xs650. I plan on upgrading to tapered bearings. I have a hookup locally to get them cheaper than online. Can someone help me with the Id/od #'s?