Search results

here's the problem-bike stalls when put in 1st gear- clutch plates sticking? that's what I thought what else can cause this>??? took right cover off dis-assemble clutch pack 7 fiber-6 steel (2fo) motor-long rod upgrade.discs out big washer,bearing,washer, remove hub can't get large spacer off...

so after a year and half of building my bike I finally tried to start it up for the first time. it cranks up but only got it to run for 15 sec. then dies, any suggestions on what to try? I've already tried to advance timing a bit and messed w/ carbs ever so slightly which seemed to help...

so, I ordered custom cables for my project, installed them this past saturday-Im using Minkuni vm34s- with cables installed the slide does not close all the way.. is this correct or not??? could have sworn I saw video saying thet should be open only a hair---help

Here I am again with the same problem! I found the correct spacer needed #11-3h3-25377-00. so I put it on yesterday and caliper mount if still rubbing disc, only thing I can think of is lack of pressure to caliper piston to push it over 1/8+ or so to center rotor on/with caliper. another Q: is...

3h3-25377-00-00

hey guys, so ,I have the bike on home-made work bench finally (back can't take the bending to ground) I have to re-visit the back rim again because I notice caliper mount is rubbing on rotor. this can't be right! I took caliper out of mount and rotor is clearly touching top of mount. WHY? not a...

hey guys, can you run both a battery and a capacitor? motor is kick only start-hhb pma-ignition--picked up a very small 12v gel battery from walmart thinking I could just use it to run lights 9head,tail,speedo) and any other acc. I decide to put on.

new tc bros. engine stand-30.00 +shipping new cam chain tool set-35.00+shipping new tc bros 2 into one throttle cable-25.00 +shipping used cam chain (good cond.) did type- make offer used 20mm rear axle-20.00 + shipping used 2 pc clutch push rod -make offer used points and advance- make offer...

I have a new tc bros 120 link chain for the bike and it appears to need shortening? is 120 the standard size? even with tire all the way back it is overlapping itself, i tend to over think stuff can't afford mistakeslol

So, yesterday I finally got around to putting oil in the rebuild, I try to kick it just to get the oil moved around (not to start) and I can stand on lever! I didn't have plugs in-motor has been done now for 2-3 months just sitting in frame while I try and wire it up. I have rags in every open...

Happy New Year ! I bought a Lincoln flux core welder couple months ago so I can add stuff that wasn't put on my frame and I'm having a really hard time seeing out of the auto darkening mask I picked up on Amazon, I even trid sun glasses under mask and still not able to see so called puddle when...

Hi guys, been awhile since I been here but have been working on the build. I'm at the wiring point now, I bought the Newest HHB kit and have started wiring it up but now am stumped at how I'm supposed to mount all these pieces. I have a fake oil tank which I have to weld to frame yet, do I just...

hey guys, I'm still putting it back together now I have more questions-#1- from block out washer sequence I have = 1mm,2mm,slide bushing,basket,1mm,bearing,2mm,hub,spring washer,tab lock,nut. right or wrong? manual and chilton only show bearing and 2mmwasher- when installed that way basket has...

hey guys, so I picked up a new cam chain from u no where and I noticed that one of my bearings gas some play...if you look at motor upside down in the rebuild position its the center bearing to left of the cam chain cog, all other bearings don't move at all but this one has some front to back...

about to close this puppy up but need to know if I should do the 5th gear upgrade?? I bought a 32 tooth rear sprocket, is that enough or should I also do the upgrade to keep the rpm down on hwy?? I live in Jersey so its alot of 65mph and more.thanks... sorry if this is a double post, I thought i...

hey guys maybe you can enlighten me, I got a 32 tooth rear sprocket from mikes xs , how will the bigger 5th work with that

im putting starter gear back on and just need to know if that wishbone clip is supposed to be in notch in case? is was not in that notch when i took it off, i have seen vids where guys says he thinks it should go there but need to know fo show...lol. ill look at manual to see what they say ..thanks

I need exact sizes for inner spacer (long) #2m0-25317-00-00 as I cant locate one, or can I use one from other models non xs??? :confused:

hey guys, so i'm about to start rebuild of my motor= 79 f.. I took oil pump apart and all looks good but uncertain of reinstallation , is there a diagram showing breakdown of each part? i ask because when i took it apart i noticed a flat washer that must have stuck to a part that later fell off...

need collars,spacer bearing,dust cap for right side of 16" mag or exact measurements to have them made. note: mag has disc brake not drum