Search results

I have a 1979 xs650 hardtail made and welded together by Ardcore. Lowered and stretched about 2-3" I forget exactly. Setup up to run on a capacitor, no battery. Custom billet triple tree. Lowered 2" front forks Billet foot controls. Has clutch hydraulic upgrade Reverse hand levers. Leather...

Looks like I'll be parting out the bike. I'd like to start with the engine, it's a 1979 with less than 6000 miles, the bike before was mint $400. The frame, is titled, it's an Ardcore hardtail welded on by Ardcore themselves. $500 Wheels $350 Forks $200 Located in Fairfax Virginia 22003

I'm stripping my project bike down. I have a 1979 xs650 engine. Less than 6k miles Bike was mint it came from. Strong compression. $400 Picked up virginia 22003

Hey guy. Project went stale after a few things happening, but looking to breathe new life into my enthusiasm. I'm running stock single disc on the front, and I have the amazon ducati slave for the hydraulic clutch conversion. Wondering if anyone has found a matching set of levers with small...

So I used kreem tank sealer, and after sitting with fuel in for 4 months its was rusty and the kreem was peeling. I have read nothing but bad about that stuff now. Anyways, im going to be using por 15 once I get all the kreem out. But when sealing it do I do the gas cap and the petcock...

So im looking to use a remote master cylinder and have it cable operated.. as I don't want the MC on the bars. I got a nissin rear MC off a MX bike... I forget exactly what but it was off like a 250. I made an actuating bracket, and im using inverted levers but I just don't get enough...

Looking to use a cable operated remote master cylinder for my front brake. Can I mount it under my engine or does it need to be higher than the front caliper to work?

I'll be converting my clutch to hydraulic using a Ducati slave cylinder (30.5mm) and using the stock caliper on the front brake. I want some cheap fairly inexpensive levers, the resevoir have to be small. I'd prefer to use the 'clear tube resevoir' mod but I'm getting confused with bore stroke...

As in title, looking for hydraulic clutch for my '80

So I would like to convert my clutch to hydraulic, but with a remote MC off say a mx bike. Has this been done, and what parts would I use (slave cylinder, remote MC or the required bore specs etc)

I need one, or possibly 2 of the bolts that hold the clutch springs in for a '80 of what ever other years are compatible.

I have just fitted inverted brake and clutch levers. Bike was working fine before, engine was without oil for about 8 weeks. But before looking at sticking plates I was wondering if anyone knew how many degrees the bolt moves (under the left hand side adjustment cover) when pressing and...

So I'm looking to order a custom front brake lone as I'm using a remote resevoir. I know it's a 10mm banjo on the caliper side, but does anyone know what angle it is for sure? I have 12* and 20* as options.

ok so I have shotgun pipes with no baffles, I know I need to re-jet...... I had my bike running while testing my new pamco pma cap setup, on a rough wiring all good. I have snice rewired it for a temp/ridable wiring setup before its stripped and redone once the frame is painted. upon starting...

Im looking for some custom brake lines that are bronze/gold with bronze/gold fittings. I cant seem to find a place that does both Posted via Mobile

I need some custom length cables/ sleves for my clutch/brake/throttle. I want to do them myself but cant find diy kits.... anyone know of any?

I have a pamco with e-advance, hhb pma and a capacitor. 1) when doing the timing does it matter what coil wire I clip onto.. left or right sat on the bike? 2) Am I looking to get the TDC mark that I put on the fly wheel to line up with TDC or FIRE mark on the HHB case sticker when its...

Looking for finished shotgun exhaust or an exhaust builder kit

I pulled the fuel lines and not 100% on how they were or what sizes to use. I have a mixture of 1/2'' and 1/4'' tube. im going to be using a single sided petcock with stock twin mikunis. Can i use a gravity fed petcock, with 1/4'' coming it, going into T splitter and running 2 more 1/4'...

Looking for some rear sets for a hard tail. Bolt or preferably weld on. pm me