Search results

Lot of Parts: Exhaust, Electrical, Crank, Bits, Etc EDIT: Everything's gone.

EDIT: All remaining parts moved here: http://www.xs650.com/forum/showthread.php?p=236403#post236403

SOLD Speedo is metric, 474.9km on the odometer. Illuminated & not a scratch on them. They come complete with mounting brackets and I'll throw in a good speedo cable and tach cable. $30 each or both for $55. Shipping Canada - $9 USA - $15 Anywhere else please contact me for a shipping...

Going to run a rear disk and keep a 20mm axle but it's gotta be longer to fit the Radian swingarm. Anyone know the best place to source one or have one made?

No need for spokes and wheel but will take them if it makes your life easier. PM with what you've got & thanks!

I was wondering if there are 17" wheels out there that I can lace up to stock xs650 hubs so that I can use modern sportbike tires? Any info is appreciated!

Will pay top dollar! #6 & 7 in this image. I also need #8 if I can get it but the priority is the former. Please let me know what you've got! Posted via Mobile

Sold.....

Hey guys, I took the bike out for its 3rd and longest ride today and the battery died after about 10 mins. Battery voltage is less than 12V at 2000+RPM so it appears it's not charging. Specs: - '75 Motor, original alternator/rotor, new brushes. - Mike's solid state regulator/rectifier...

From a pile of parts...to her first ride tonight! This is my first XS and the first bike I've put together from a pile of parts. It was supposed to be plug & play but it wasn't quite like that :D This project began back in September when I was given a frame and a bucket of parts by a neighbor...

I've finished wiring up my XS and everything tested/worked ok. Then I knocked the bike over and it looks like I've knocked something loose because all of a sudden nothing works. With my multimeter, I touch the positive terminal of the battery and ground to the motor and get a reading of...

I've got the Keihin PWK carbs that came with pod filters. I've got Belray foam filter oil that I use for the dirtbike and am wondering if this will be acceptable for the pods? Belray doesn't advise against using it in pod filters but it's my first go with them, so if you know, please say...

Just got my XS running and took it for its maiden voyage up the driveway and back. The motor is fresh with 1st over pistons, PWK carbs, Pamco, etc. I have not gotten the electric starter functioning yet but can start it with the kickstarter ok. I have not yet synced carbs or adjusted timing...

And what does it do? On my '75, it has green/white, yellow and black wires and is a small grey box about 2" long. Do I need it? If not, how can I bypass it? Posted via Mobile

Purchased a Mike's harness for my '75 (447) and there are a couple discrepancies I need help with: There are two connector blocks in the harness that don't show up on the wiring diagram. One comes out of the harness near the coils (I'll call it #1), the other is at the front (I'll call it...

Ok so maybe 'blessing' is a better word. I have three questions (photo below): 1. Do I have this wired correctly? I'm figuring it out as I go and would like an expert's opinion. Pamcopete? 2. There are 4 leftover wires in this photo. Two are orange and two are gray and using my circuit...

I'm thinking of removing a set of bronze bushings from a rear drum swingarm to install in a rear disc swingarm but they're in there TIGHT. I don't want to destroy them in the process. Any tips on how to get them out cleanly without gouging them? Cheers! Posted via Mobile

I can't seem to get my wheel spacers to line up properly and could use a hand from you fellas. First off, I believe I have the correct swingarm/wheel combo on the bike. Rear drum, and the matching swingarm. I installed new bearings and am pretty sure they're seated properly. I have 3...

....because I'm looking for proper calipers for them. 34mm tubes, dual disc. Anyone know what year they're from? Thanks!