Media added by YAM277

Navigation

  1. XS650 Originals and Restorations 178
  2. XS650 Choppers 31
  3. XS650 Bobbers 126
  4. XS650 Trackers 163
  5. XS650 Cafe Racers 102
  6. XS650 Slightly Modified 147
Browse albums

Media comments

  • gggGary
    Jim's Paint
    Love Jim's painting!
  • Tim Meaders
    Spoiler
    This was my original one-off design, it was scrapped and replaced with a new wider version.
  • P
    Spoiler
    where can I get this spoiler

Most media items

  1. YAM277
    510

    YAM277

  2. TwoManyXS1Bs
    502

    TwoManyXS1Bs

  3. I am Carbon
    500

    I am Carbon

  4. Mike G
    472

    Mike G

  5. Mailman
    463

    Mailman

Media statistics

Categories
6
Albums
2,942
Uploaded media
25,481
Embedded media
18
Comments
1,628
Disk usage
4.6 GB
IMG 02-If you are taking out the Tach Drive Gear Assembly, without removing the R.H. Case cover, you might drop #8 on the chart, called the "Shim". If

IMG 02-If you are taking out the Tach Drive Gear Assembly, without removing the R.H. Case cover, you might drop #8 on the chart, called the "Shim". If

  • 0
  • 0
IMG_1410

IMG_1410

  • 0
  • 0
IMG 10 The first bit to be used (after applying the light coat of grease to the surrounding areas) was a 11/32 bit. Start slowly, only go in a 1/2 inc

IMG 10 The first bit to be used (after applying the light coat of grease to the surrounding areas) was a 11/32 bit. Start slowly, only go in a 1/2 inc

  • 0
  • 0
IMG 0804- Remove both plastic collars and smooth out the metal neck before applying new diaphragm.

IMG 0804- Remove both plastic collars and smooth out the metal neck before applying new diaphragm.

  • 0
  • 0
IMG_1143

IMG_1143

  • 0
  • 0
IMG 0818-JBM Industries replacements.

IMG 0818-JBM Industries replacements.

  • 0
  • 0
IMG 27- Using a pair of Channellocks, the springs really have to be compressed to fit properly. The flat sides of the springs need to fully pocket int

IMG 27- Using a pair of Channellocks, the springs really have to be compressed to fit properly. The flat sides of the springs need to fully pocket int

  • 0
  • 0
IMG 0779- Remove old crusty O ring

IMG 0779- Remove old crusty O ring

  • 0
  • 0
IMG 22-Primary Drive Gear on left, Clutch Housing on right. Backsides facing up.

IMG 22-Primary Drive Gear on left, Clutch Housing on right. Backsides facing up.

  • 0
  • 0
IMG 0783- A little bit of liquid soap, to ease it in.

IMG 0783- A little bit of liquid soap, to ease it in.

  • 0
  • 0
IMG_1126

IMG_1126

  • 0
  • 0
XS650 Wallys

XS650 Wallys

  • 0
  • 0
IMG 20- Old Rivet, will be replaced by new hex Allen bolt.

IMG 20- Old Rivet, will be replaced by new hex Allen bolt.

  • 0
  • 0
XS 650

XS 650

  • 0
  • 0
IMG_1134

IMG_1134

  • 0
  • 0
IMG_1130

IMG_1130

  • 0
  • 0
IMG 18- I used a magnetic screwdriver to swipe the leftover shavings, to make sure no metallic pieces were left over.

IMG 18- I used a magnetic screwdriver to swipe the leftover shavings, to make sure no metallic pieces were left over.

  • 0
  • 0
IMG 0803- Remove the nasty.

IMG 0803- Remove the nasty.

  • 0
  • 0
IMG_1406

IMG_1406

  • 0
  • 0
IMG 0785- seated needle jet(Z-2) with new o ring

IMG 0785- seated needle jet(Z-2) with new o ring

  • 0
  • 0
XS650 painted beauty

XS650 painted beauty

  • 0
  • 0
IMG 0817

IMG 0817

  • 0
  • 0
IMG 09-Just a pic of the assembly, showing the "Shim", slightly installed off the bottom of the gear drive.

IMG 09-Just a pic of the assembly, showing the "Shim", slightly installed off the bottom of the gear drive.

  • 0
  • 0
xs 650

xs 650

  • 0
  • 0
Back
Top