Search results

Hello all, just wondering, is Slingshot Cycles still around, I'm looking for a one piece front ss brake line for my 75.

i shortened the wire on one side of my E-Advancer by like 3" will that mess it up, and how close is too close to have the e-advancer to the coil. Thanks

Forgive me if this info is out there, I've been searching but can't seem to find much. Can an antigravity 8cell work with a pma, will it charge correctly?

hi all, got a needle jet from mikesxs but it has no markings on it, so do I have to trust that I received the correct one or is there a way I can make sure it's what I need, can I measure it somehow? I don't get how there is no size stamped on it.

Free new IZUMI Rear Drive Chain - Heavy Duty 530 x 104, why free, just like to give back to a community that's given me so much. PM me if you need it.

(2) VM34-168 carbs, new in box. Make reasonable offer.

Hi all, i can't seem to find a difinitive answer to this question, maybe there is none, well here goes, Is there a rule of thumb when lowering you fork. If my rear shocks are an inch shorter do I lower my fork an inch, or am I not thinking about this the right way.

My new cam chain is so tight that the chain tentioner can't be adjusted in any way, how will this effect my valve and timing adjustments.

Hi all, Does any one know the dimensions of Mikesxs Ultimate high output ignition coil, HxWxD and bolt hole to hole on center

Any help would be appreciated, I got a 1975 (447-121558) barn find, I'm doing a complete rebuild of the engine,bottom end done. Now I'm in the process of putting the top end together, Here's where i go down the rabbit hole, the cam that was in the engine when i tore it down was shot, so i had...

Hey guys, I'm doing a engine rebuild and I just finished painting and oven curing the VHT paint, the paint job looked great....except for one minor detail....I hate the color:doh: can I paint over the cured VHT or do I have to strip it all off:banghead:

hello all, so here's my story, I needed a project to get me through a long Connectcuit winter, although with the way the weather is going it doesn't seem like it will be that long...anyway I got a 1975 barn find basket case for a $100 bucks, stuck engine, looked like it was buried since 1975...

I just installed a Pamco E advancer and having trouble with timing, when I time it using timing light the pamco sensor has to be in the full advance position to get timing marks within the fire range at 1200 rpm, everything was installed and wired correctly I have 60 degree rotor, all three...

Really could use some help, I have a 79sf,I removed my RLU and light checker, I have looked at so many posts I'm going blind. I connected the blue/black for RLU and blue and blue/yellow for the light checker, still no headlight. Then I checked the blue/black wire for voltage and there is none, I...

I got this seat from eBay, has anyone installed this seat on a 79 special, they said it was a bolt on but I'm probably gonna have to cut the frame. Any help would be great.

Does anyone know if there is a bolt on cafe seat available for a stock 79, mikexs has a great looking seat but not for 79. Has anyone modified this seat to fit or know wear I can get one, I search hi and low with no luck. Thanks :bike:

Hi, I'm trying to view your videos on valve adjustment but it says privet viewing only, is there a way I can check them out? :(

Ok, here is probably a stupid question so forgive me, but if I check my oil level with the dipstick lines facing up I'm low on oil, if I check with line facing down the level is perfect. Which way should you face the lines to get an true level, or am I just being a dipstick. Is a 79 thanks:shrug:

Hi guys, I'm a total newb to the xs so forgive me if this is posted somewhere else. I'm getting reddy to install a pamco in a 79, I know the condensers between the motor mounts. But what is the large condenser above the coils, I mean I think its a condenser, it has like a see thru plastic cap...